background image

English

English-1

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT 

USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE 

PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING 

TO QUALIFIED SERVICE PERSONNEL.

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED 

FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT 

THE POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER 

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause 

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit 

has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION

CAUTION:

CAUTION: 

Please use the power cord provided with this display in accordance with the table below. If a power cord is not 

supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the  

AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

Plug Type

North America

European 

Continental

U.K.

Chinese

Japanese

Plug Shape

Country

U.S.A./Canada

EU (except U.K.)

U.K.

China

Japan

Voltage

120*

230

230

220

100

* When operating the monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply  

voltage of the AC power outlet being used.

NOTE: 

This product can only be serviced in the country where it was purchased.

Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. 

ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, 

Norway, Spain, Sweden, U.K. 

E

nErgy

 S

tar

 is a U.S. registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective owners. 

As an 

E

nErgy

 S

tar

®

 Partner, NEC Display Solutions of America, Inc. has determined that this product meets the 

E

nErgy

 S

tar

 

guidelines for energy efficiency. The 

E

nErgy

 S

tar

 emblem does not represent EPA endorsement of any product or service.

VESA is trademark in the United States and other countries owned by the Video Electronics Standards Association.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC 

in the United States and other countries.

•  The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.
•  The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.

        

Summary of Contents for MultiSync E232WMT




















Reviews: