manualshive.com logo in svg

NEC MG-SIP, Configuration Manual

Share
Download
NEC MG-SIP Configuration Manual Download Page 17

MG-SIP

  

Page 17 of 75 

5/8/2009 

7. MG-SIP Startup and Programming 

7.1 Maintenance Console Settings 

Use a serial connection client such as Hyperterminal to connect MG-SIP16 on a software basis. Be sure to 
connect RS-232C cable (straight cable) between MG-SIP16 and the Maintenance Console (PC) when 
initially setting up MG-SIP16. 
 

STEP 1:

 Open a communication software Hyper Terminal on the Maintenance Console, and set up the 

connection with MG-SIP16. 
(1) Startup Windows on the Maintenance Console. 
(2) Click 

Start

, point to 

Programs 

Æ

 

Accessories 

Æ

 

Communications

, and then click 

Hyper 

Terminal 

icon. 

(3) Communication setting dialog box appears. Enter the name, icon, connection type, and port settings. 

Note: 

There is no specific note in assigning the name and icon. Select the connection type 

COM1 (depending on the PC). Port settings should be specified as follows: 

 

 

 
STEP 2:

 Power ON the switch on the rear panel of MG-SIP16. Linux installed in MG-SIP16 is activated. 

 

STEP 3:

 The following message is displayed on the Maintenance Console screen. 

NOTE 1

 

 

Summary of Contents for MG-SIP


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands