NEC FA Series Installation And Maintenance Manual Download Page 39

Page: 39 / 131

English

- 37

11. Installation without a frame set

A recommended example of installation when using the brackets is shown below. Please prepare the

bracket by yourself. Ask a technician or your retailer for the installation procedure when not using

the brackets.

Install the brackets to the frame as shown in the figure below.
Use screws with a length adapted to the cabinet thickness (30 mm). Use also brackets with a

sufficient thickness to hold the screws.

48 mm*

88 mm*

30 mm

4-M6

*: Please check Diagram (

English-127

) for dimensions.

Installation example

Frame

Bracket

Cabinet

564 mm*

608 mm

342 mm

Adjust the horizontality of the lowest row.

For installation, please refer to the “

9. Install the cabinets

”.

Summary of Contents for FA Series




































































































































Search results

Summary of Contents for FA Series

Reviews:

Related manuals for FA Series

Brands by name

Popular brands

NEC FA Series, Installation And Maintenance Manual

Search results

Summary of Contents for FA Series

Reviews:

Related manuals for FA Series

Brands by name

Popular brands