manualshive.com logo in svg

NEC Express5800/B120b-d, User Manual, Page: 11 / 294

Share
Download
NEC Express5800/B120b-d User Manual Download Page 11

v

Chapter 5    Installing the Operating System with Express Setup............................... 5-1

About Express Setup ....................................................................................................................5-2
Windows Server 2008...................................................................................................................5-3

Notes on Windows Installation.................................................................................................5-3
Flow of Setup ...........................................................................................................................5-8
Installing the Windows Server 2008.........................................................................................5-9
Installing and Setting Device Drivers.....................................................................................5-22
The procedure to set PAE option............................................................................................5-23
Setting for Solving Problems .................................................................................................5-23

Windows Server 2003.................................................................................................................5-24

Notes on Windows Installation...............................................................................................5-24
Flow of Setup .........................................................................................................................5-29
Installing the Windows Server 2003.......................................................................................5-30
Installing and Setting Device Drivers.....................................................................................5-39
The procedure to set PAE option............................................................................................5-40
Setting for Solving Problems .................................................................................................5-41

Setting for Solving Problems......................................................................................................5-42
Installing Maintenance Utilities..................................................................................................5-53
Updating the System...................................................................................................................5-53
Making Backup Copies of System Information..........................................................................5-54

Installing with the OEM-FD for Mass Storage Device ..........................................................5-55

Chapter 6  Installing and Using Utilities ....................................................................... 6-1

NEC EXPRESSBUILDER...........................................................................................................6-2

Autorun Menu ..........................................................................................................................6-6

Parameter File Creator..................................................................................................................6-7

Parameter File ..........................................................................................................................6-8

NEC ESMPRO ...........................................................................................................................6-20
Universal RAID Utility...............................................................................................................6-22

Setup with Express Setup.......................................................................................................6-22
Manual Setup .........................................................................................................................6-22
Using Universal RAID Utility via Network...........................................................................6-22

NEC Product Info Collection Utility ..........................................................................................6-23

Installation..............................................................................................................................6-23
Using Utility...........................................................................................................................6-24
Uninstallation .........................................................................................................................6-24

Chapter 7  Maintenance.................................................................................................. 7-1

Making Backup Copies ................................................................................................................7-1
System Diagnostics.......................................................................................................................7-2

Test Items .................................................................................................................................7-2
Startup and Exit of System Diagnostics ...................................................................................7-3

Summary of Contents for Express5800/B120b-d







































































































































































































































































































Reviews:

No comments