background image

English

English-15

Specifications

Monitor Specifications

MultiSync EA232WMi

Notes

LCD Module

Diagonal:

58.4 cm/23.0 inches

Active matrix; thin film transistor (TFT) liquid crystal

Viewable Image Size:

58.4 cm/23.0 inches

display (LCD); 0.265 mm dot pitch; 250 cd/m

2

 white

Native Resolution (Pixel Count):

1920 x 1080

luminance; 1000:1 contrast ratio, typical
(25000:1 contrast ratio, Dynamic).

Input Signal

DVI:

DVI-D 24pin:

Digital RGB

DVI (HDCP)

DisplayPort:

DisplayPort Connector:

Digital RGB

DisplayPort Complies with Standard V1.1a,
applicable to HDCP

VGA:

15pin Mini D-sub:

Analog RGB

0.7 Vp-p/75 ohm

Sync

Separate sync.TTL level Positive/Negative
Composite sync.TTL level Positive/Negative
Sync on Green
(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)

Display Colours

16,777,216

Depends on display card used.

Synchronization Range

Horizontal:

31.5 kHz to 83 kHz

Automatically

Vertical:

56.0 Hz to 76.0 Hz (Over SXGA: 60Hz)

Automatically

Viewing Angle

Left/Right:

±89° (CR > 10)

Up/Down:

±89° (CR > 10)

Resolutions Supported

720 x 400*

1

: VGA text

Some systems may not support all modes listed.

640 x 480*

1

 @ 60 Hz to 75 Hz

800 x 600*

1

 @ 56 Hz to 75 Hz

832 x 624*

1

 @ 75 Hz

1024 x 768*

1

 @ 60 Hz to 75 Hz

1152 x 870*

1

 @ 75 Hz

1280 x 1024*

1

 @ 60 Hz to 75 Hz

1400 x 1050*

1

 @ 60 Hz

1440 x 900*

1

 @ 60 Hz

1920 x 1080 @ 60 Hz............................. NEC DISPLAY SOLUTIONS cites recommended.

Active

Landscape: Horiz.:

510 mm/20.0 inches

Display Area

Vert.:

287 mm/11.3 inches

Portrait: Horiz.:

287 mm/11.3 inches

Vert.:

510 mm/20.0 inches

USB Hub

I/P:

USB Specification Revision 2.0

Port:

Upstream 1
Downstream 4

Load Current:

Maximum 0.5A per port

AUDIO

AUDIO Input:

STEREO Mini Jack:

Analog Audio

Stereo L/R 500mV rms 20 Kohm

DisplayPort Connector:

Digital Audio

PCM 2ch 32, 44.1, 48 KHz (16/20/24bit)

Headphone Output:

STEREO Mini Jack:

Headphone Impedance 32 Ohm

Speakers

Practical Audio Output:

1.0 W + 1.0 W

Power Supply

AC 100-240 V ~ 50/60 Hz

Current Rating

1.05-0.55 A (with USB and Audio)

Power

Maximun Operation:

53 W

Consumption

Normal Operation:

31 W (Default setting, USB/Audio sleeping)

Dimensions

Landscape:

550.1 mm (W) x 379.1 - 489.1 mm (H) x 220.0 mm (D)
21.7 inches (W) x 14.9 - 19.3 inches (H) x 8.7 inches (D)

Portrait:

329.0 mm (W) x 565.1 - 600.6 mm (H) x 220.0 mm (D)
13.0 inches (W) x 22.2 - 23.6 inches (H) x 8.7 inches (D)

Height Adjustment:

110.0 mm/4.3 inches (Landscape condition)
35.5 mm/1.4 inches (Portrait condition)

Weight

7.4 kg (16.3 lbs)

Environmental Considerations

Operating Temperature:

5°C to 35°C / 41°F to 95°F

Humidity:

20% to 80%

Altitude:

0 to 6,562 Feet / 0 to 2,000 m

Storage Temperature:

-10°C to 60°C / 14°F to 140°F

Humidity:

10% to 85%

Altitude:

0 to 40,000 Feet / 0 to 12,192 m

*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.

NOTE:

Technical specifications are subject to change without notice.

Summary of Contents for EA232WMI-BK























Reviews: