NEC Dterm DTL-RPT-2 Manual Download Page 10

1 - 2

Legal and Warranty Information

___________________________________________________________________________________

___________________________________________________________________________________

Issue 1.0

D

term

 Cordless DECT

Unplug this product from the wall outlet and refer servicing to qualified service 
personnel under the following conditions:

When the power supply cord is damaged or frayed.

If liquid has been spilled onto the product.

If the product has been exposed to water or rain.

If the product does not operate normally when following the operating 
instructions. Adjust only those controls that are covered by the operating 
instructions. Improper adjustment of other controls can result in damage, and 
will often require extensive work by a qualified technician to restore the product 
to normal operation.

If the product has been dropped, or the case has been damaged.

If the product exhibits a distinct change in performance.

S

ECTION

 

2

I

MPORTANT

 E

LECTRICAL

 C

ONSIDERATIONS

Unplug all electrical appliances when you know an electrical storm is approaching. 
Lightning can pass through your household wiring and damage any device connected 
to it. This repeater is no exception.

Changes or modifications to this product not expressly approved by NEC Corporation 
of America, or operation of this product in any way other than as detailed by this 
manual, could void your authority to operate this product.

S

ECTION

 

3

FCC  R

EGULATORY

 I

NFORMATION

3.1

Part 15 Compliance

This device complies with part 15 of the FCC rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, 
and (2) This device must accept any interference received, including 
interference that may cause undesired operation. Privacy of communications 
may not be ensured when using this phone.

Certification numbers:

FCC ID: AMWUU228

Industry Canada IC: 513C-UU228

Do not attempt to unplug any appliance during an electrical storm.

Summary of Contents for Dterm DTL-RPT-2































Reviews: