manualshive.com logo in svg

NEC Dterm Cordless Lite, Owner'S Manual, Page: 14 / 56

Share
Download
NEC Dterm Cordless Lite Owner'S Manual Download Page 14

NEC America, Inc.

Issue 1

D

term 

Cordless Lite

 Owner’s Manual

1 - 5

Caution:

To reduce the risk of fire or injury to persons by the battery,
read and follow these instructions.

1.

Use only the appropriate type and size battery pack

specified in the manual.

2.

Do not dispose of the battery pack in a fire, the cell
may explode.

3.

Do not open or mutilate the battery pack.  Released
electrolyte is corrosive and can cause damage to the
eyes or skin.  It may be toxic if swallowed.

4.

Exercise care in handling the battery in order not to
short the battery with conducting materials such as
rings, bracelets, and buttons.  The battery or
conductor can overheat and cause burns.

5.

Charge the battery pack provided with or identified for
use with this product only in accordance with the
instructions and limitations specified in the instruction
manual provided for this product.

6.

Observe proper polarity orientation between the
battery pack and battery charger.

Privacy

Cordless telephones are radio devices.  Communications
between the handset and base of the cordless telephone are
accomplished by means of radio waves which are broadcast
over the open airways.  Because of the inherent physical
properties of radio waves, communication can be received by
radio receiving devices other than your own telephone unit,
consequently, any communications using the cordless
telephone may not be private.

Summary of Contents for Dterm Cordless Lite

























































Reviews:

No comments