NEC DT920 User Manual Download

Page: 27 / 104

OUTLINE

CONNECTING HEADSET

For DT900 series, 3 types of headset are
available; wired headset, EHS headset, and
Bluetooth



headset (DT930 Touch Panel model

only). Following explains about connecting wired
headset and EHS headset cable. About
Bluetooth



headset connecting, please refer to

“

TO SET Bluetooth DEVICE

”.

CONNECTING HEADSET WITH
TERMINAL

According to the following procedure,

Headset is connected to HEADSET
Connector which is located bottom of
terminal.

For the headset that is supported,
please contact the NEC's dealer or
NEC.

The headset which can be connected
to the terminal is "HW510
(A10)/HW251N (A10) (manufactured
by Plantronics)".

HOW TO CONNECT HEADSET

Plug the modular plug of headset into the
HEADSET connector on the bottom of terminal.

Fit the headset cord into the groove to be fixed.

(1)  Terminal
(2)  Modular Plug
(3)  Cord
(4)  Groove Modular Plug
(5)  HEADSET connector

Refer to the

HEADSET OPERATION

(1)

(2)

(3)

(4)

(5)

Summary of Contents for DT920









































































































Search results

Summary of Contents for DT920

Reviews:

Related manuals for DT920

Brands by name

Popular brands

NEC DT920, User Manual

Search results

Summary of Contents for DT920

Reviews:

Related manuals for DT920

Brands by name

Popular brands