background image

English

English-11

Specifications

Monitor Specifications

AccuSync AS192 Monitor

Notes

LCD Module

Diagonal:

48.2 cm/19.0 inches

Active matrix, thin film transistor (TFT)

Viewable Image Size:

48.2 cm/19.0 inches

liquid crystal display (LCD); 0.294 mm dot

Native Resolution (Pixel Count):

1280 x 1024

pitch; 250 cd/m

2

 white luminance, 1000:1

contrast ratio, typical.

Input Signal

15pin Mini D-sub:

Analog RGB

0.7 Vp-p/75 ohms

Sync

Separate sync. TTL level (Positive/Negative)

DVI-D

Digital RGB

DVI(HDCP)

Display Colors

Analog input:

16.7 M

Depends on display card used.

Viewing Angle

Left/Right:

-80°/+80° (CR>10)

Up/Down:

-75°/+85° (CR>10)

Synchronization Range

Horizontal:

31.5 kHz to 81.1 kHz

Automatically

Vertical:

56 Hz to 76 Hz

Automatically

 Resolutions Supported

Landscape:

720 x 400*

1

: VGA text

Some systems may not support all

640 x 480*

1

 at 60 Hz to 75 Hz

modes listed.

800 x 600*

1

 at 56 Hz to 75 Hz

832 x 624*

1

 at 75 Hz

1024 x 768*

1

 at 60 Hz to 75 Hz

1152 x 864*

1

 at 75 Hz

1152 x 870*

1

 at 75 Hz

1280 x 960*

1

 at 60 Hz to 75 Hz

Recommended resolution is 60 Hz for

1280 x 1024*

1

 at 60 Hz to 75 Hz..................optimal display performance.

Active Display Area

 Horizontal:

376 mm

Vertical:

301 mm

Power Supply

100 - 240 V ~ 50/60 Hz

Current Rating

0.55 - 0.3 A

Power

Maximun Operation:

25 W

Consumption

Normal Operation:

19 W

Dimensions

Landscape:

412.5 mm (W) x 403.1 mm (H) x 205.1 mm (D)
16.2 inches (W) x 15.9 inches (H) x 8.1 inches (D)

Weight

3.4 kg (7.5 lbs)

Environmental Considerations

Operating Temperature:

5°C to 35°C/41°F to 95°F

Humidity:

20% to 80%

Altitude:

0 to 2,000 m/0 to 6,562 Feet

Storage Temperature:

-10°C to 60°C/14°F to 140°F

Humidity:

10% to 85%

Altitude:

0 to 12,192 m/0 to 40,000 Feet

*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.

NOTE:

Technical specifications are subject to change without notice.

Summary of Contents for AccuSync AS192


















Reviews: