NEC 120Ra-1 Installation Manual Download Page 5

Page: 5 / 12

120Ra-1 Pentium III Processor Installation 5

Top Covers

The server includes front and rear top covers. To install a processor into the
system board of the server, you must remove the rear top cover.

CAUTION

For proper cooling and airflow, do not operate the system
with the top covers removed. Always replace the covers
before powering on the system.

WARNING

If you are removing the top covers after the system is set up,
you must first power off the system and all external devices
and then

Unplug

the system power cord

Removing the Rear Top Cover

To remove the rear top cover:

Loosen the captive thumbscrew securing the top cover to the rear panel.
See Figure 2. Slide the top cover towards the rear of the server chassis until
its tab fasteners unlock.

Lift the top cover up and away from the chassis.

Figure 2. Removing the Top Cover

Summary of Contents for 120Ra-1













Search results

Summary of Contents for 120Ra-1

Reviews:

Related manuals for 120Ra-1

Brands by name

Popular brands

NEC 120Ra-1, Installation Manual

Search results

Summary of Contents for 120Ra-1

Reviews:

Related manuals for 120Ra-1

Brands by name

Popular brands