manualshive.com logo in svg

Neary 555, Operator'S Manual, Page: 8 / 29

Share
Download
Neary 555 Operator'S Manual Download Page 8

8

SPECIFICATIONS

Traversing Switches

Solid state, non-contacting proximity switches.

Overall Width

71" [181 cm]

Overall Height

69" [175 cm] with door closed, 87" [221 cm] with door open

Overall Depth

42" [107 cm]without workstation, 79" [201 cm] with optional workstation

Weight

1450 lbs. [658 kg] 1650 lbs shipping weight [748 kg]

Base Construction

Precision  heavy duty reinforced welded steel base

Carriage Rails

Precision Ground, Hardened Steel - 1.000 Dia. [25.4 mm]

Grind Head Motor

1HP AC Motor, 3450 RPM

Spin Motor

.20 HP Fan Cooled Variable Speed DC Motor

Sound Level

More than 75 Dba, Less than 95 Dba

Auto Traverse

Belt driven with easy to engage clamp system

Control System

*Safety grind motor and spin drive door interrupt switches
*Reversible Spin drive for variable speed Spin or variable torque relief functions
*Variable speed traverse control.

Options:

*Manual Winch and Boom Kit, Electric Winch and Boom Kit or Workstation.

GETTING TO KNOW YOUR GRINDER

Summary of Contents for 555






























Reviews:

No comments