SPEAKER REAR VIEW
2
Connecting the Plug-In Connector
Wiring to the VM-Series Speaker
UP/DOWN
TILT
PLUG-IN
CONNECTOR
ROTATE
RING
For a Vertical Mount, the speaker’s
Plug-In Receptacle
(C)
and Speaker
Mount Bracket
(D)
must be rotated.
Remove the four screws from the
Plug-In Receptacle and two screws
from the Speaker Mount Bracket,
and rotate each 90-degrees clockwise.
Next, securely re-attach the screws.
PLUG-IN
RECEPTACLE
When the Plug-In Connector has been properly attached and secured, the speaker cable conn-
ection should look as shown
(1)
, ready to be coupled with an amplifier.
3
A
Situating the VM-Series Speaker
onto the Wall Mount Bracket
C
E
ROTATE
B
C
WALL
MOUNT
BRACKET
ON
WALL
E
ON
WALL
D
A
The Speaker’s Mount Bracket is already
attached to the speaker’s rear and the Wall
Mount Bracket has been firmly secured to a
wall/flat surface. Now position the Speaker
Mount above the Wall Mount Bracket and
slowly lower the “socket” that is the Speaker
Mount Bracket
(A)
down on to the “ball” that
is the Wall Mount Bracket
(B)
, allowing the
Threaded Screw
(C)
on the Wall Mount
Bracket to slide up through the open slot
(D)
of the Speaker Mount Bracket. Continue to
lower the Speaker Assembly until it is now
resting upon the Wall Mount Bracket. At this
point the Speaker Assembly is able to hang
from the Wall Bracket, which will now free
up both hands for adjusting the speaker’s
position or additional wiring.
The Speaker can now be positioned in a variety of angles. To focus the speaker
orientation in an upward or a downward manner, tilt the speaker in a back-and-forth
motion within the Speaker Bracket Slot
(D)
and Mount Bracket Thread
(C)
axis. The
Speaker can also be rotated on an angle or side-to-side using the “Ball & Socket”
design of the brackets and then locked into position by the Wall Mount Bracket
“teeth”
(E)
as well as the Clamping Knob (see section 3B).
MOUNTED HORIZONTALLY OR VERTICALLY,
THE SPEAKER CAN BE ROTATED/ANGLED
BOTH LEFT OR RIGHT, UP AND DOWN
4
Connecting a Safety Cable
to the VM-Series Speaker
SAFETY CABLE
ATTACHMENT POINT
(SCREW)
SAFETY CABLE
(USER-SUPPLIED)
TO AMP
The VM-Series Speakers come factory-ready for a Horizontal Mount. To connect the speaker wiring to
a speaker, simply insert the Plug-In Connector
(B)
directly into the Plug-In Receptacle
(A)
located on the
rear of the speaker, just to the right of the Speaker Mount Bracket. NOTE: Both the Plug-In Receptacle
and the Plug-In Connector are “KEYED” items and fit together correctly in only one orientation. Once
the Plug-In Connector has been inserted, rotate the Ring at the end of the connector to fully tighten
(see Plug-In Detail).
A
B
SIDE VIEW
HORIZONTAL MOUNT
SPEAKER REAR VIEW
TO
AMP
SPEAKER REAR VIEW
SPEAKER MOUNT BRACKET
PLUG -IN RECEPTACLE
C
D
C
D
1
2
PLUG-IN
DETAIL
A
Insert the Plug-In Connector (see Plug-In Detail), and the speaker cable
connection should look as shown
(2)
, ready to be coupled with an amplifier.
SPEAKER
MOUNT BRACKET
D
A
MOUNT DETAIL
To finalize the mounting procedure, first insert the
provided washer up and into the Clamping Knob
(F).
With the Speaker Assembly now in its final desired
orientation, secure it into position by bringing the
Clamping Knob
(F)
down on to the exposed portion of
the Wall Mount Thread
(C)
and then screw the knob
into place. A 1/2” Socket or Nut Driver can be used
to firmly tighten the Clamping Knob so that the entire
assembly is now secured.
W
ALL
WALL MOUNT
BRACKET
CLAMPING KNOB
SPEAKER
MOUNT
BRACKET
W
ALL
HORIZONTAL MOUNT
F
C
F
C
CLAMPING KNOB
1/2” SOCKET
OR NUT DRIVER
1/2” SOCKET OR
NUT DRIVER
VERTICAL
MOUNT
SPEAKER
MOUNT
BRACKET
3
B
SIDE VIEW
SIDE VIEW
CLAMPING
KNOB
RUBBER
WASHER
F
WALL MOUNT
BRACKET
SPEAKER REAR VIEW
VERTICAL
MOUNT
HORIZONTAL MOUNT
It is HIGHLY recommended that a safety cable be used
to help further secure the VM-Series speaker. There is
a Safety Cable Attachment Point Screw
(A)
located on
the rear of the speaker. Slightly loosen this Screw, then
connect a (user-supplied) safety cable by winding the
cable around it.
After fully re-tightening the Safety Screw, the cable now
attached to the speaker can be connected to another
fastening point (ex. ceiling beam) to provide additional
security against disconnection/falling.
A
A
VERTICAL
MOUNT
YOU MUST ACCURATELY FOLLOW THE INSTRUCTIONS FOR ALL THE
PARTS INVOLVED IN THIS INSTALLATION. FAILURE TO DO SO CAN
CAUSE SERIOUS INJURY OR DEATH TO YOURSELF OR OTHERS AND
MAY EXPOSE YOU TO POSSIBLE LEGAL ACTION. PLEASE CONSULT
A PROFESSIONAL INSTALLER IF YOU ARE UNCERTAIN OR HAVE ANY
QUESTIONS REGARDING THE SPEAKER INSTALLATION.
Mounting the VM-Series Speaker
onto the Wall Mount Bracket
