manualshive.com logo in svg

NDT Systems Avenger EZ-AWS, Operator'S Manual

Share
Download
NDT Systems Avenger EZ-AWS Operator'S Manual Download Page 33

32

32

5.0  OUTPUTS

There is a Mini-Phono type female receptacle on the top of the enclosure of TG400.  There is an
RS-232C serial output available at this receptacle. There is also a connector on the bottom of
the gage which supports USB as well  An optional cable assembly is available from NDT
Systems.

5.1  Output Choices.

5.2.1  RS-232C Output Specifications.

Baud Rate

19200

Parity

None

Data Bits

8

Stop Bits

1

The TG400’s RS-232C output connector (Mini Phono) is located on the Top side of the  enclosure. 

6.0  BATTERY PACK AND CHARGER

The TG400 is powered by 3 NiMH Rechargable ‘AA’ style batteries inserted into the bottom panel via
the rear panel access cap. The gage is charged via an external battery charger. Once fully charged
the TG400 will run for up to 20+ hours before requiring another charge. Charge time is 6-8 hours for a
full charge from empty.

The TG400 is also capable of running from Alkaline batteries, available from many outlets, should you
need to use the unit where remote power for charging is not available. if the charger/eliminator is
plugged in, as the alkaline batteries are installed damage to the gage by leaking batteries will be likely.
The damage is obvious and is not covered under warranty.

Batteries are to be installed with the tip facing into the gage. Installing the batteries in the wrong will
cause damage to the gage.

Summary of Contents for Avenger EZ-AWS




































Reviews:

No comments

Brands by name

Popular brands

Load more brands