![background image](http://html1.mh-extra.com/html/nds/dometic-lse-105-bf/dometic-lse-105-bf_installation-and-operating-manual_3770680017.webp)
EN
Dometic reserves the right to change product appearance and product specifications.
8 Technical description
The solar panels are particularly flat and bonded directly to the vehicle roof. The solar panels can be applied to slight-
ly curved roof surfaces.
The solar system can be extended by further solar panels of the same power.
The solar charge controller (accessories) is connected between the solar panels and the battery to ensure the correct
charging current of the batteries and to protect the batteries against over voltage and deep discharge.
9 Installing the solar panel
WARNING! Electrocution hazard
Completely cover all solar panels with an opaque material during installation to prevent electricity from
being generated.
NOTICE! Damage hazard
Ensure that the junction box (accessories) and the roof duct (accessories) are properly sealed and that the
roof duct is glued tightly to the roof so that no moisture can leak into the junction box or through the roof.
Installation location
When selecting the installation location, consider the following:
• The mounting surface must be even and stable enough to support the solar panel.
• Ensure that the designated mounting surface is sufficiently dimensioned.
• Observe the maximum flexibility of the solar panel (see
).
• Ensure there is enough room to access the solar panels and other fixed components for future maintenance.
• Ensure not to block any existing ventilation openings on the vehicle.
• Shading can reduce the performance of the solar panel. Ensure that fixed components, such as air condition-
ers or opened satellite antennas, do not shade the solar panel.
• Choose a location with direct sunlight for optimal performance.
• Place several solar panels as close to each other as possible.
• Do not glue the solar panels or roof ducts to rubberized surfaces (e.g. exterior planking), as the adhesion of the
glue is not guaranteed.
Preparing the installation
1.
Mark the bonding surfaces on the vehicle.
2. Grind the bonding surfaces on the vehicle with abrasive fleece (
1
,
3. Clean the bonding surfaces on the vehicle (
2
).
15
Summary of Contents for Dometic LSE 105 BF
