background image

MSL-200 

CNC LATHE 

MAINTENANCE MANUAL 

NCT Ipari Elektronikai Kft. 

 30 / 32 

10 September 2018 

H-1148 Budapest, Fogarasi út 7. 
Phone: +36 1 467 6300 
www.nct.hu 
 

6.4

 

Lubrication of hydraulic system 

1.

 

Please use ISO viscosity 32 or 46 hydraulic oil. Please don’t use viscosity degree 68 hy-
draulic oil during winner, because this kind oil’s viscosity too high which easy cause bed 
in draft or cavitation issue. 

2.

 

Please change hydraulic oil after 3 months (or 750 hours) at first time. After that, please 
change oil every half year (or 1500 hours). 

3.

 

Please put hydraulic unit at ventilating place. 

4.

 

Please keep oil tank temperature lower than 60 

5.

 

Please don’t mix different brand hydraulic oil to avoid additive deteriorated. 

6.

 

When  hydraulic  oil  becomes  deterioration,  add  new  oil  can’t  extend  using  year,  all  of 
hydraulic oil needed to change to new oil. 

1  Hole for release oil 
2  Oil scale 
3  Hole for add oil 

 

 

6.5

 

Lubrication position 

Auto lubrication pump install on machine right side, please make sure quantity of oil enough 
or not, if the quantity not enough, please add oil. 

 

 

 

Summary of Contents for MSL-200

































Reviews:

Related manuals for MSL-200