manualshive.com logo in svg

NCS NCS-C250C, Instruction Manual

Share
Download
NCS NCS-C250C Instruction Manual Download Page 26

15.0

 Contacting NCS

NCS wants you to experience trouble free operation of our equipment.  If you have any 
questions, comments or need technical help, please use the following resources:

1.

Go to the web site, 

www.ncsradio.com

.

Here you will find the latest instruction manuals, any factory developed 
modifications and Frequently Asked Questions.  Schematics for all NCS products 
may be found at 

www.ncsradio.com/schematics

 .

2.

Email us at 

[email protected]

Be sure to include all pertinent information, e.g. make and model of radios, how 
they’re connected to the C250C , detailed description of any problems, antenna 
and grounding configurations, etc.

3. Telephone us toll-free at 888-883-5788.

Be near your equipment and have the manuals for your radios available.  We will 
do our best to help you using our technical expertise.

NCS-C250C Instruction Manual Rev J

Copyright  © 2004-20010 New Communications Solutions, LLC

26

Summary of Contents for NCS-C250C





























Reviews:

No comments

Brands by name

Popular brands

Load more brands