NCR 6003-K001-V003 Installation Instructions Manual Download | Manualshive

Page: 94 / 163

background image

80

Figure 142

4)

Identify the vacant end along the top rail (top left or top right; whichever side the
OPTIC power supplies do not reside).

Caution: Do not proceed with the installation of the kit if another component is
installed opposite of the OPTIC power supply where the heater is supposed to be
installed. Contact customer service.
5)

Orient and mount the heater assembly as shown using one of the provided 6-32
screws (006-8611215) and nuts (006-8611426) with nut on the bottom. See Figure
143.

Figure 143

6)

The screw and nut should be installed at the locations called out in Figure 144 and
Figure 145.

«
...
92
93
94
95
96
...
»

Summary of Contents for 6003-K001-V003




































































































































































Reviews:

No comments

Related manuals for 6003-K001-V003

Brand: Farmet Pages: 102

Brand: Hach Pages: 66

Brand: Hach Pages: 14

Brand: Hach Pages: 144

QuikChem 8500 2 Series

Brand: Hach Pages: 80

Brand: Hach Pages: 178

Brand: Hach Pages: 32

Brand: hager Pages: 4

Brand: MagCore Pages: 80

Brand: MagCore Pages: 80

Brand: WalkMed Pages: 2

Brand: Walinga Pages: 20

Brand: Salter Pages: 18

Brand: Salter Pages: 42

Brand: Salter Pages: 47

Brand: Salter Pages: 35

Brand: Salter Pages: 40

M-041 INDOOR CROSS

Brand: Salter Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands