NCR 6003-K001-V003 Installation Instructions Manual Download | Manualshive

Page: 123 / 163

background image

109

Figure 194

6)

Allow the door panel to tilt forward until it rests in the horizontal position.

7)

Repeat steps 1) - 6) for the opposite side of the dispenser to allow internal access
to both sides of the dispenser.

8)

Acquire the heater (NCR heater assembly) and OPTIC heater wire guard (497-
0522796).

9)

Slide the wire guard (497-0522796) around the NCR heater assembly so that the
edge of the bracket aligns with the Helix, Tokheim C alignment mark as shown in
Figure 195.

Figure 195

10)

Insert and tighten two of the thread forming 006-8626667 screws at the locations
shown in Figure 196 to secure the wire guard (497-0522796) to the NCR heater
assembly.

«
...
121
122
123
124
125
...
»

Summary of Contents for 6003-K001-V003




































































































































































Reviews:

No comments

Related manuals for 6003-K001-V003

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: 3M Pages: 2

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

Brand: Ecco Pages: 2

Brand: Landoll Pages: 94

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Dynapro ET 355 Monitor HL

Brand: 3M Pages: 23

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Pablo Pages: 7

Brand: VBM Pages: 36

Brand: W&H Med Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands