To change between REGULAR and YARD modes:
l) Turn on the DCC system.
2) Unplug your Cab04 from the cab bus
3) Plug the cab back in while holding down the SELECT LOCO button.
4) Release the SELECT LOCO button. The cab will now enter its internal setup
program indicated by a flashing LED.
5) Press "2" to enter Yard or normal select mode. The LED flash rate slows to
indicate the cab is ready for you to select which mode
6) Press "1" for Yard mode or press "O" for Normal mode. If you enter a number
outside this range it will not be accepted and the cab will continue to wait for "1"
or "0
11
•
To change BALLISTIC TRACKING rate {CAB04e only):
I) Turn on the DCC system.
2) Unplug your Cab04 from the cab bus
3) Plug the cab back in while holding down the SELECT LOCO button.
4) Release the SELECT LOCO button. The cab will now enter its internal setup
program indicated by a flashing LED.
5) Press "3" to enter the ballistic tracking rate setup mode. Notice the flashing of
the LED slows to indicating it is ready to accept the new data.
6) Ballistic tracking provides a means for the speed to ramp up/down quickly if the
knob is turned fast. It will ramp up/down slowly if the knob is turned slowly. This
gives you very fine control by turning the knob slowly yet allows quickly changing
speed by turning it fast. The factory setting is 3. Lower numbers lower the
sensitivity and higher numbers increase the sensitivity to how fast the knob is
turned. If you enter a number outside this range it will not be accepted and the
cab will continue to wait for a number in the range of Oto 7. The valid range is
Oto 7.
Setting the OPTION key:
I) Turn on the command station
2) Unplug your cab from the command station
3) Press and hold down the SELECT LOCO button while plugging in the cab. The
cab will now enter its internal setup program. This is indicated by a flashing
status LED.
4) Press "4" to enter OPTION key setup mode. Notice the flashing of the LED
slows indicating it's ready to accept the new key value.
5) Enter a new value for the OPTION key from the table on the next page, followed
by the ENTER key. If you enter a number less than 64 or greater than 128 the
LED will flash rapidly indicating an error. If you get an error press SELECT
LOCO to clear the error and go back to step 2.
Last revised: 4. December 2006
Page 4
Cab04p
.I
Table of values for OPTION button and "Shifted" buttons
Value
Kev Name
Value
Kev Name
64
Enter
97
Program on Main
65
Proaram
98
Set Clock
66
Recall
99
Use program track
67
Direction tonnle
100
Setup command station
68
Setuo consist
101
Setuo Procab
69
Add loco to consist
102
Setuo macros
70
Delete loco from consist
103
Setuo old consist
71
Kill consist
104
Setun advanced consist
72
Select loco
105
Display LCD lines 3 and 4
73
Horn button down
106
Forward
74
1 Saeed stea faster
107
Reverse
75
1 Saeed stea slower
108
Select Signal
76
Emeraencv Stoa
109
reserved
77
Bell
110
reserved
78
SelectAccv
111
Momentum
79
Expn (Expansion) key
112
F10
80
Headliaht, Zero key
113
F11
81
F1, number 1 key
114
F12
82
F2, number 2 key
115
reserved
83
F3, number 3 key
116
reserved
84
F4, number 4 key
117
reserved
85
F5, number 5 key
118
reserved
86
F6, number 6 key
119
reserved
87
F7, number 7 key
120
reserved
88
F8, number 8 key
121
reserved
89
F9, number 9 key
122
F13-F28 control
90
4/10 saeed steas faster
123
Alt momentary button down
91
4/10 saeed steas slower
124
Alt momentary button up
92
Macro
125
"no key" pressed
93
28/128 saeed select
126
reserved
94
Brake
127
do not use
95
Horn button up
128
"Saecial" shift key
96
Assign Loco to Cab
129
reserved
Notes on OPTION key settings:
Some of the possible values for the OPTION key are impractical as they require
many visual prompts on the LCD of a ProCab. In the above table the most practical
key values are listed in bold type.
If you are adventurous you can try some other key values. We use Programming
On The Main fairly often.
1. Set the option key value to 97
2. Use Programming on the Main with your ProCab and record the key strokes to
access CV programming. (PROGRAM ON MAIN, ENTER, ENTER, 2, CV#, CV
value, ENTER [the last ENTER exits programming])
3. Press OPTION on the Cab04 and notice the LED will light indicating data entry
mode. Press the keys you recorded in step 2.
Last revised: 28. July 2006
Page 5
Cab04p
