background image

 

25 

 

 

TROUBLESHOOTING 

Problem 

Possible cause 

Solution 

The device 

does not start 

Low fuel. 

Check the fuel level and add fuel if necessary. 

Spark plug flooded or damaged. 

Check, clean or replace the spark plug. 

Interruption in ignition system 

or contaminated fuel insert. 

Have the gardening equipment service repaired, it is best 

to entrust the mower to an authorized service center. 

Engine fires 

unevenly 

Contaminated air filter. 

Replace or wash the filter in soapy water and gently soak 

in engine oil. 

Low quality fuel. 

Remove fuel and refuel the mower with high-quality fuel. 

Clogged fuel line, no fuel or old fuel. 

Clean the fuel line, check fuel delivery, add fresh fuel. 

Water, oil or dirt in the fuel system. 

Drain the carburettor with the fuel sink screw and top up 

with fresh mixture. 

Oil flooded carburettor after tilting the 

mower to the side. 

Clean the carburettor from oil. 

The engine 

goes out 

Badly adjusted brake cable. 

Make the appropriate adjustment. 

Dirty air filter. 

Replace the filter. 

The engine is 

smoking 

Muffler flooded with oil after tilting the 

mower to the side. 

Top up oil and start the mower for 15 minutes, the oil will 

burn itself. 

Excessive 

vibration. 

Knife adapter damaged. 

Replace it. 

Crooked motor shaft (after impact). 

Stop the engine immediately and remove the spark plug 

cap. Tighten all screws and make other appropriate 

repairs. If the vibration does not disappear, entrust the 

repair to an authorized service center. 

Loose assembly of components. 

The mower 

does not 

throw grass in 

the bin 

The grass is too high. 

Mow twice. 

Wet grass. 

Do not mow. 

Inverted or worn cutting knife. 

Insert the cutting knife correctly or replace it. 

Dirty lawn mower chassis. 

Clean the mower chassis. 

A dirty or overfilled basket. 

Empty and clean the basket. 

Engine speed too low. 

Adjust the turnover at the authorized service center. 

Wheel drive 

not working 

(drive 

version) 

Worn or damaged drive belt. 

Replace the wheel drive belt. 

Cut grass lying down. 

Clean the transmission mechanism. 

Incorrectly adjusted drive cable. 

Adjust the drive cable. 

Worn drive protection mechanism. 

Replace the gear. 

 

WARRANTY AND SERVICE 

The  product  purchased  by  you  is  intended  for  amateur  (hobby)  use  only.  If  the  equipment  is  used  for  other  purposes 
(commercial, professional), it will lose the guarantor's liability for the purchased equipment. You can find information on the 
warranty and the NAX service network in the attached warranty card. 

Remember  that  the  machine  should  be  cleaned  after  each  use.  Keeping  the  equipment  clean  will  ensure  long-term  and 
reliable operation. Cleaning, maintenance and periodic inspections are not repairs. Authorized NAC services may perform 
these activities as part of a paid service. 

Summary of Contents for NAX 1000S

































Reviews: