NavLinkz RL3-MIB-4 Manual Download

Page: 1 / 19

Version 22.02.2018

HW:

GD(V97)/(V33)

RL3-MIB4

r.LiNK

Video inserter

RL3-MIB-4

Compatible with VAG infotainment systems from MIB/MIB2/MIB II

construction kits - High und Standard executions

Compatible with Audi vehicles with MMI ( on MIB base)

Bentley vehicles with MIB with 8“ monitor

Lamborghini vehicles with MIB with monitor in instrument

Porsche vehicles with PCM 4.0

Seat vehicles with Media System Plus – navigation system PLUS

Skoda vehicles with Columbus, Amundsen and Bolero

VW vehicles with Discovery Pro, Discover Media, Composition Media

Video-inserter for one rear-view camera and two more video inputs

Product features



Video-inserter for factory-infotainment systems



CVBS Input for one rear-view camera



2 CVBS Video-inputs for after-market Video sources (e.g. DVD-Player, DVB-T Tuner)



Automatic switching to rear-view camera input on engagement of the reverse gear



Activatable parking guide lines for rear-view camera (not available for all vehicles)



Video-in-motion (ONLY for connected video-sources)



AV-inputs NTSC compatible

Summary of Contents for RL3-MIB-4




















Search results

Summary of Contents for RL3-MIB-4

Reviews:

Related manuals for RL3-MIB-4

Brands by name

Popular brands

NavLinkz RL3-MIB-4, Manual

Search results

Summary of Contents for RL3-MIB-4

Reviews:

Related manuals for RL3-MIB-4

Brands by name

Popular brands