BATTERY REPLACEMENT
Notification “Sensor battery low” on LCD indicates the empty state of sensor battery. Please replace sensor battery according to sensor
user manual.
If time and date of display unit set to default value check the battery for real time clock battery back-up (1 x 3 V CR2032) and replace it
if needed:
unscrew all 4 plastic screws to open display unit enclosure. Note that the screws can be pulled out only at the correct angle.
Disconnect main power supply. Replace the battery for real time clock battery back-up (1 x 3 V CR2032). Connect main power supply.
Reattach the front panel of the display unit.
RESET OF DISPLAY UNIT
With upper button pressed at power ON, R
ESET is performed (all settings except »Sensor Address«, »WS Cal. Factor« and »WD
Cal.« go to default values).
TROUBLESHOOTING
Symptom
Action
The display unit cannot read the
sensor
(“No data” appears on the display)
- check if the correct sensor address is set on the display unit
- make sure the sensor is not in sleep mode (turn the cups to wake up the sensor)
- check the sensor battery
– replace the battery if needed
- check the operation at a reduced distance to the display unit
Interrupting and weak sensor signal
- check for obstructions between sensor and display unit
- place the sensor or display unit in a different position with better signal reception
- reduce distance to the display unit
- change or add antenna for the display unit
Unresponsive display unit
- check 1 x 3 V CR2032 Lithium battery in display unit
– replace the battery if needed
- remove 1 x 3 V CR2032 Lithium battery and main power supply for 1 minute to reset
display unit.
Time and date set to default value
- check the battery for real time clock battery back-up (1 x 3 V CR2032) - replace if needed
APPLICABLE ONLY FOR W410XB/D AND W410XL/D MODELS:
SMARTPHONE COMPATIBILITY
A data packet is transmitted over Bluetooth every second. With the
free “Windy Anemometer” application you can read the data of the
current, average, and maximum wind speed, as well as wind direction and temperature, or view history graphs on your smartphone.
In the application settings menu, always set the address corresponding to the address of the W410 receiving sensor.
The range is up to 40 meters. Inside a building, the range is much smaller. The range also varies with the type of smartphone or tablet.
Application “WINDY ANEMOMETER” can be downloaded from Google Play or Apple Store.
Android: Applications requires device with Android 4.3 or newer with Bluetooth Low Energy (BLE).
Apple: In iOS settings for the Windy Anemometer application configure parameter "Allow Location Access" to "While Using the App".
APPLICABLE ONLY FOR W410XW/D AND W410XL/D MODELS:
WI-FI COMPATIBILITY
When display unit receive data from wind sensor, data packet is transmitted through Wi-
Fi connection to “Navis Live Data” web
interface. On Navis
“Live Data” web interface it can be observed data of current, average and maximum wind speed, wind direction,
temperature or view history graphs.
NAVIS LIVE DATA WEB INTERFACE
For registering display unit to Navis
“Live Data” web interface please see “Navis Live Data” web interface user manual.
SETTINGS: WI-FI PARAMETERS
PARAMETER: Scan for Wi-Fi
To search nearby Wi-
Fi networks select parameter “Scan for Wi-Fi”.
If there are Wi-Fi networks available use UP, DOWN and SET keys to select desire Wi-Fi.
For enter password use UP and DOWN keys for select individual character and SET key to confirm selected character.
After entering password, confirm with OK.
If there is no password, leave input field blank and confirm with OK.
PARAMETER: Wi-Fi
For manual entry of Wi-Fi network SSID
select parameter “Wi-Fi” and use UP and DOWN keys for selecting individual character and
SET key to confirm selected character. After entering Wi-Fi network SSID, confirm with OK.
For enter password use UP and DOWN keys for select individual character and SET key to confirm selected character.
After entering password, confirm with OK.
If there is no password, leave input field blank and confirm with OK.
SERIAL NUMBER
S/N parameter show Wi-Fi serial number of display unit.
“WI-FI” ICON
Display unit is c
onnected to WiFi network when “WiFi” icon is displayed on main screen.
Display unit sent data to Navis
“Live Data” portal when “WiFi” icon blinks on main screen.
If there is no “WiFi” icon displayed on main screen please check your Wi-Fi connection or Wi-Fi parameters of display unit.
