background image

 

NAVIOR-24S 

™ 

 

     

Appendix E 

NMEA Tool kit User’s Guide 

 

205 

 

 
NAVIOR-24S ™

 

    Revision 

V1.00 20.05.2008 

The STATISTIC window 

 
The STATISTIC window showing Figure IV-30. 

 

 

Figure IV-30. The STATISTIC window 
 

The STATISTIC window (Figure IV-30) displays the following information: 
  - 

– averaged latitude; 

  - 

– averaged longitude; 

  - 

H

 – averaged altitude; 

  - 

rms2D

 – planar RMS, calculated over position statistics, m 

  - 

rmsH

 – altitude RMS, calculated over position statistics; 

  - 

rmsV

 – speed RMS, calculated over position statistics, m; 

  - 

Nall 

– a number of solutions in statistics; 

  - 

N

 – a number of solution over which the average coordinates are averaged (always 

less or   

equal than Nall); 

  - 

MaxHDOP

 (user defined) – a maximal possible HDOP for a solution to be 

included in    

statistics; 

  - 

MaxVDOP

 (user defined) – a maximal possible HDOP for a solution to be 

included in    

statistics; 

 

 

-

 DIFF

 only – only the solution that used differential augmentations are included in 

   statistics. 

Summary of Contents for A.467855.020





































































































































































































































Reviews: