Navigator LP240BK User Manual Download Page 25

25 

manner and all passengers are in safety. Operators should fully read the manual 

before using the boat. 

RETURNS 

Based on current regulations, we accept our boats within 15 days of purchase in the 

same condition it was with all of the original packaging, documentation and parts. In 

the same condition means that the boat is new, unused and free of any damage. Be 

careful while unpacking the boat if you’re using a sharp object as you might damage 

it. 

PRE-ORDERS 

At Navigator Inflatable Boats we typically operate on a pre-order basis, custom-crafting 

boats that fit your needs & preferences. We charge a 30% deposit payment before the 

boat gets into production & shipping. 

Our Warranty DOES NOT cover: 

Natural material ageing, product wear and tear or any kind of accident 

Improper use of the boat or attached accessories or use not in line with the boat’s 

manual, which includes but is not limited to oversized motor usage or overloading of 

capacity 

Any alterations, repairs, modifications or part removals not approved by our technical 

department and the use of accessories supplied by other vendors 

Improper protection against Sunlight & temperature changes (storage during 

summer/winter), including consequential damage to the tubes & seam separation due 

to heat exposure. 

Loss of the documentation pertaining to the boat 

Fabric damage caused by harsh chemicals, fuel, toxic chemicals, high-pressure 

washing, punctures, wear & tear due to a rocky shore surface. Discoloration and color 

fading. 

Damage caused by insects or other animals, including rodents 

Malfunctions caused by force majeure (fire, acts of God, etc.). 

Damage as a result of shipping, warehousing, or storage. Any shipping will be the 

responsibility of the purchaser. Any units shipped for repair will be the responsibility of 

the purchaser. Navigator Inflatable Boats will then ship (if required) the repaired unit 

or repaired parts or new part(s) to the purchaser at the responsibility of the purchaser. 

Most of the inflatable boats, independently of the brand, lose pressure over some time 

and it is universally not considered to be a warranty issue. 

This warranty does NOT cover product that: Has not been assembled, used, and 

maintained as stated in owner's manual accompanying the Product; Damage caused 

by accident; Has been abused, misused or improperly operated; Has been repaired, 

modified or tampered with by someone other than Navigator Boats or their designated 

representative; Do not to attempt to repair the boat yourself as it will void your 

warranty. Navigator LLC’s sole exclusive obligation under this warranty is limited to, 

at our option, repairing a defective part, replacing such part or refunding the purchase 

price of the Navigator Boats product. The repair, replacement of the boat, replacement 

Summary of Contents for LP240BK



























Reviews: