background image

3. Step 3: Communication set-up 

A ft er the cable co nnectio ns and DIP sw itches are set- up,  the co mmunicatio n set- up sho uld be do ne. 

3.1 Master set-up 

A ft er the pow er ON, each FND1 w ill display o n the PCB  as below: 

Unit 

Master Unit 

Slav e 1 Unit 

Slav e  2 Unit 

FND1 

IHD.Dill l5D.llll  l5D.llll 

FND1  display: Master set-up 

3.2 Slave set-up 

A ft er  the  master  set- up,  push  the SW3  and SW4  o f  slav e  1  unit  simultaneo usly  mo re  than 3 

seco nds. 

FND1 o f  the slav e  1  unit w ill be changed to  "S001 ". 

Slav e  2  unit also  can be set- up as abov e. 

A ft er the slav e  set- up,  each FND1 w ill be changed o n  the PCB  as below: 

Unit 

Master Unit 

Slav e  1 Unit 

FND1 

IHD.llll 

15.QQ LI 

FND1 display: Slave set-up 

3.3 Set-up finish 

Slav e  2 Unit 

l5.ilil21 

A ft er  the  slav e  set- up,  push  the SW3  and SW4  o f  the  master  unit  simultaneo usly  mo re  than 3 

seco nds. 

All the FND w ill be changed to  the setting temperature display and set- up pro cedures are finished. 

4. Master unit Change 

I t  is alw ay s  po ssible to  change the master unit. Aft er all units power o ff,  choo se o ne o f  the units as 

the master unit and change the DIP SW2 (#1  sw itch)  acco rding to  master unit change. 

T hro ugho ut co mmunicatio n  set- up (St ep 3)  master unit change w ill be do ne. 

5. Slave unit Addition/Removal 

I t  is alw ay s  po ssible to  add o r  remov e the slav e  unit. Aft er all unit pow er OFF,  the co mmunicatio n 

cable is added o r  remov ed o n the PCB  acco rding to  slav e  unit additio n o r  remov al. 

Summary of Contents for CC-180





























































Reviews: