Navico Simrad I3005 Page 25 Operator'S Manual Download | Manualshive

Page: 25 / 52

background image

Time

Controls the local time zone offset, and the format of the time and
date.

Restore defaults

Restores selected settings to default factory values.

Files

File management system. Used to display selected content of the
unit for export, and to browse storage devices connected to the
unit.

About

Displays copyright information, software version, and technical
information for this unit.

Advanced

Page settings

Ú

Note:

Type approved pages are labelled with the wheelmark

icon in the Pages settings dialog.

Software setup

| I3005/I3007 Operator Manual

25

«
...
23
24
25
26
27
...
»

Summary of Contents for Simrad I3005





















































Reviews:

No comments

Related manuals for Simrad I3005

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: Baileigh Industrial Pages: 40

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brand: Eazyzap Pages: 32

Brand: Obdstar Pages: 42

Brand: PAS Systems International Pages: 24

MARK V Alcovisor

Brand: PAS Systems International Pages: 20

Brand: PARRY Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands