Nav TV Zen M Installation Manual Download Page 4

BHM 

04/24/18 

NTV-DOC319  

 

 

 

4 | 

P a g e

 

 

Wire Side 

*This remote wire must be used for aftermarket amplifier remote for proper functionality. 

If installing more than 

one amplifier/DSP, a relay must be used for reliable turn-on (500mA max). 

*NOTE: DownMix ON mixes vocals from center channel into Front and Rear L+R output channels. 

 

ZEN-M Installation 

 

1.

 

If this vehicle has a factory amplifier, it must be removed and the ZEN-M can be installed into its place. 
If this vehicle is not amplified from factory, install the ZEN-M behind the radio.   
 

2.

 

Connect the following wires from the 
provided 

power harness

 

 

 

 

 

3.

 

Before connecting power to the ZEN-M,

 adjust dip-switch settings for the desired 

options:  
 

 

 

4.

 

If using analog RCAs for signal to the amplifier, connect according to the reference chart below. 

WARNING: Do not connect RCA cables to this interface until all amplifiers/external processors are 
properly grounded. Failure to do this may cause damage to the interface and VOID the warranty!

 

10 

11 

12 

Left 

Front 

Right 

Front 

Left 

Front 

Right 

Front 

Left 

Front 

Right 

Front 

Left Rear 

Door 

Right Rear 

Door 

Left Rear 

Center 

Right Rear 

Center 

Center 

Sub 

 

5.

 

If using TOSLink for signal to the amplifier, connect the cable to the TOSLink port shown on page 2. 

NOTE: both Analog and Digital output sound simultaneously, regardless of which type is used.

 

6.

 

Connect the provided 

MOST Fiber Cable

 from the 

(previously removed) amplifier, or from the radio’s 

fiber port to the MOST port on the ZEN-M. 

NOTE: if fiber already exists at the head unit (for SAT radio, 

etc), you must add the provided MOST fiber cable into the OEM MOST loop (see next page).

 

ZEN-M pin 

Color 

To vehicle: 

Yellow 

12v (+) 

Constant

 

Violet 

--Reserved, NOT USED-- 

Black 

Ground (-) 

Blue 

12v (+) remote output* 

 

Time 

Alignment 

Attenuation 

TOSLink 

DownMix* 

Loudness 

Vehicle Settings 

Position 

DIP 1 

DIP 2 

DIP 3 

DIP 4* 

DIP 5 

DIP 6 

  

UP  

(off) 

  

Front Row

 

 

  

Full Scale 

output (0 dB) 

  

DownMix ON

 

 

Loudness 

OFF 

 

OFF 

 

OFF 

 

DOWN

 

(on) 

  

Driver Focused

 

  

-12 dB output 

  

DownMix OFF

 

  

Loudness ON  

 

OFF 

 

OFF 

Summary of Contents for Zen M












Reviews: