background image

1 | 

P a g e

Toyota 6 navigation system application guide 

2015 – 2016   Sienna 

(Pioneer Apps Radio) 

P10692 

** Toyota 6 navigation system only compatible to vehicles listed above.  Only compatible 
radio is Pioneer Apps radio (Entune Plus radio with 7” touch screen).  Please verify the radio 
has APPS button on front plate for this system to install and work properly.  

This system only applicable to the 

Pioneer

 

radio.  If your radio is 

NOT a Pioneer radio (usually be identified with “P” in front of the 
radio number located on the radio front plate), please contact your 
distributor immediately.  Any damage to this installation by 
wrongly attempt to install inapplicable combination will not be 
warranted. 

WARRANTY DISCLAIMER NOTICE!

 Radio removal, disassembly, installation 

of Navigation Electronics, and Radio re-assembly / re-installation is the responsibility 
of the installer.  It is recommended that you contact a professional installer that is 
experienced with proper work methods involving electronics and knowledgeable of 
specific procedures for radio disassembly, Navigation Electronics installation, and re-
assembly / re-installation of the Radio Head Unit in the vehicle.  

INSTALLATION 

DAMAGE TO THE VEHICLE RADIO HEAD UNIT IS EXPRESSLY NOT 
COVERED UNDER THE PRODUCT WARRANTY. 

To avoid dangerous distractions that may lead to an accident, the driver should never 
operate the system while the vehicle is in motion.  Before installing the product, the 
seller should inform the end-user of proper use and compliance with the proper 
instructions and all states and federal laws. 

Before beginning your installation, familiarize yourself with the installation 
instructions and the Navigation system components. 

CAUTION:

 It is advisable to disconnect the negative battery cable for 3 minutes 

before beginning installation, to avoid unintended air bag deployment.  Note and 
record any anti-theft radio codes prior to disconnecting. 

This is a general installation guide for navigation system only.  There will not be 
any instruction on dash / radio removal.  Please refer to Toyota service manual 
for removing radio from dash.

 

Summary of Contents for NTV-KIT625













Reviews: