Nav TV NTV-KIT597 User Manual Download Page 11

 

Toyota 5 Navigation System Installation 

10 | 

P a g e

 

Trouble Shooting 

Please follow all the steps in this installation manual, failure to do so might 
void the product warranty and damage the factory radio 

Power 

GPS Module has (2) led lights as indicators when system is power on.  
Both led lights should lit with good power.  If any of the light is 
dimmed, you should check for B+ and ACC power sources. 

Display 

No Display 

1.

 

There are two led lights at the GPS module to indicate data 
and power.  If led lights are OFF and radio is ON, check the 
power fuse inside the black box from the main harness 

2.

 

Check all wiring connectors for any loose connection 

3.

 

Check all wiring shielding for any damage during the 
installation process 

4.

 

Check all wiring for any type of damage 

5.

 

Check PCB ribbon cables for loose, misalignment, or 
damage 

No Touch Response 

1.

 

Check both Radio mode and NAV mode for touch responses 

2.

 

Check led lights for power and data indications 

3.

 

Check 2in1 TP/LCD IN cable for any loose connection, or 
damage 

4.

 

Check PCB ribbon cables for loose, misalignment, or 
damage 
 

No GPS software loaded, touch screen alignment screen occurred 

Check map SD card at GPS module, see any sign of missing, 
loose, pop-out, misalignment, or damage 

Sound 

1.

 

Check all cable for connections to Audio Box for loose, or damage 

2.

 

Check software volume settings, ensure volume is not muted 

3.

 

Check connections at radio for loose, damaged wires 

NTV-DOC226 

Summary of Contents for NTV-KIT597












Reviews: