Nav TV NTV-KIT558 Installation Instructions Manual Download | Manualshive

Page: 12 / 19

background image

Connect the power harness from the vehicle interface
harness to the navigation control module.

Connect the speaker interface harness to the
navigation control module.

Find the threaded end of the GPS antenna and connect
it to the navigation control module.

Connect the vehicle interface harness to the factory
wiring harness on the car. (

Note

: the large factory

harness includes a locking retainer clip.)

NTV-DOC218

«
...
10
11
12
13
14
...
»

Summary of Contents for NTV-KIT558




















Reviews:

No comments

Related manuals for NTV-KIT558

G-Series system

Brand: Raymarine Pages: 36

Brand: VDO Pages: 2

Brand: Alpine Pages: 16

Brand: Clifford Pages: 65

Brand: Viking Pages: 6

nuvi 800 series

Brand: Garmin Pages: 12

980915 - TrafficKit - NavTraffic Receiver

Brand: Magellan Pages: 86

Brand: Metra Electronics Pages: 16

Brand: Xomax Pages: 19

BMW-MINI XM Direct

Brand: Discount Car Stereo Pages: 7

Brand: Boss Audio Systems Pages: 16

Brand: Elenberg Pages: 31

Brand: Fusion Pages: 28

Stealthbox SB-F-FOC5DR/10TW3

Brand: JL Audio Pages: 6

Brand: Blitz Pages: 33

Brand: Clarion Pages: 70

RVS CXS solutions inView 360 HD

Brand: Safe Fleet Pages: 25

HXS 635 AVANTGARDE

Brand: HELIX Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands