3
Do not place equipment in direct sunlight as ultra violet
rays can damage shields and upholstery.
NET WT. 10 OZ. (283.5g)
STOCK NO.
RG 60127
DANGER! EXTREMELY FLAMMABLE. HARMFUL OR FATAL IF SWALLOWED.
CONTENTS UNDER PRESSURE. SEEBACK PANEL.
DANGER! EXTREMEMENT INFLAMMABLE.
CONTENU SOUS PRESSION. VOIR ETIQUETT AL'ENDOS.
■
Cleans/Lubricates/Protects
■
Homogenized/No Kerosene/No Wax
■
Non-Toxic/Environmentally Safe
■
Nettote/Lubrifie/Protege
■
Produit Homogénéisé/Formule
D'avant-Garde/Sans Cire
■
Non-Toxique/Sans Effet Sur
E'environnement
PART
NUMBER
19-1160
*TFL 50
Wet
Lubricant
Recommended
for Nautilus
Machines.
Lubrication
Cleaning
1. UPHOLSTERY CLEANING AND PROTECTION
A. Keep pads free of perspiration at all times.
B. Clean and disinfect upholstery at the end of each
day, especially areas where perspiration and scalp
oil collect.
C. Clean all outside surfaces with non-abrasive, non-
chlorinated household cleaners. Nautilus
Disinfectant Cleaner is an effective upholstery care
product.
2. CLEANING AND CARE OF PAINTED
SURFACES
A. Wipe painted surfaces with a
damp cloth and car wax.
B. Let dry and buff with a dry
cloth.
3. CLEANING AND CARE OF ABS PLASTIC
SHIELDING
A. Clean with non-abrasive, non-
chlorinated household cleaners.
B. Vacuum or wipe dust from
recessed areas and surfaces
WARNING
Do not lubricate
MINI WEIGHTS.
May cause damage
and
VOID
WARRANTY.
MOVING PARTS
A. To clean and lubricate guide rods, apply TFL#50
Wet Lubricant to a clean cloth then use to wipe
rods.
Note: The hydraulic unit only needs adjustment if the
seat will not stay in position.
1. Remove CLEVIS and COTTER PINS. Remove
CIRCULAR COTTER PINS by lifting up the wire that crosses
over straight end of pin, see Figure 1. Save all PINS.
2. Use a flat blade screwdriver to gently unsnap CABLE
from LEVER MECHANISM. Be careful not to break cable
fitting.
3. Remove hydraulic unit from machine, loosen NUT by
backing it down ROD. Hold LEVER MECHANISM and twist
SHAFT until there is free play in LEVER, as shown by "B" in
Figure 1.
4. Hold LEVER MECHANISM and twist SHAFT (as shown
by "C" in Figure 3) until LEVER free play is gone, then back
off 1/8 turn. Tighten NUT against LEVER MECHANISM.
The
NUT MUST BE PROPERLY TIGHTENED
to keep hydraulic
unit in adjustment.
5. Twist SHAFT slightly to realign the top and bottom
clevis pin holes.
6. Use pliers to snap and lock the CABLE on to the LEVER
MECHANISM.
7. Reposition the hydraulic unit on machine and insert
CLEVIS and COTTER PINS. The circular COTTER PINS can
be pushed into holes.
8. The HANDLE NUT should be tight against the
HANDLE HOUSING, see Figure 2. The HANDLE LEVER
should touch the GRIP when squeezed. If it does not touch,
adjust as follows:
a. Loosen the HANDLE NUT by turning counter
clockwise.
b. Turn the ADJUSTMENT BARREL clockwise until the
HANDLE LEVER has approximately 1/4" free play.
c. Tighten the HANDLE NUT against the HANDLE
HOUSING.
Hydraulic Unit Adjustment
3. SHIELD REMOVAL
Nautilus® 2ST machines are equipped with quick-
release shield fasteners. To remove Quick-Release
shielding, gently pull shielding away from the frame.
Use a proper screwdriver to remove front shielding,
which is attached to the frame with screws.
HIGH PRESSURE : DO NOT LUBRICATE
ROD. SEAL DAMAGE WILL OCCUR.
EYE AND INJECTION HAZARD EXISTS.
Figure 1
HANDLE
NUT
ADJUSTMENT
BARREL
HANDLE HOUSING
HANDLE
LEVER
1/4" free play
Figure 2
or COTTER PIN
CLEVIS
PIN
NUT
LEVER
MECHANISM
A
B
SHAFT
LEVER
C
HIGH PRESSURE :
DO NO
T LUBRICA
TE
R
OD
. SEAL D
AMA
GE
WILL OCCUR.
EYE AND INJECTION HAZARD EXISTS.
HIGH PRESSURE :
DO NO
T LUBRICA
TE
R
OD
. SEAL D
AMA
GE
WILL OCCUR.
EYE AND INJECTION HAZARD EXISTS.
HIGH PRESSURE :
DO NO
T LUBRICA
TE
R
OD
. SEAL D
AMA
GE
WILL OCCUR.
EYE AND INJECTION HAZARD EXISTS.
CIRCULAR COTTER PIN
CABLE
Detergent/
Disinfectant-Odor
Counteractant
Detergente/
Desinfectante
y Neutralizante
de Olores
Keep out of Reach of
Children • For Industrial
Use Only
HEAL
TH
FIRE
REACTIVE
PART
NUMBER
19-1175
Detergent/Disinfectant Odor Counteractant
QUIK FILL A-
33
