Nautilus Hyosung MONiMAX8200QTN Operator'S Manual Download Page 45

Page: 45 / 120

Chapter4. Receipt Printer (SPR60) Operator Manual

4-4

Nautilus Hyosung, Inc.

Paper Specification

► Paper specification

Paper type

Continuous /marked paper

Paper supply method

Paper roll

Paper width

80mm

Paper weight

55g

～

100g

Thermal layer

Outward/Inward

Paper roll specification

Optional ID of paper roll core: ф18
Minimum ID of paper roll: ф24
Ma

ximum OD of paper roll: ф220mm

<Note!> The supported paper thickness and paper roll diameter is as followings when there is

Presenter module:

Paper thickness

Min paper roll ID

Remarks

55-80 um

Ф24

80-100 um

Ф31

► Recommended Paper:

1. Recommended continuous paper:

Paper type

Manufacturer

FD200

OJI Paper CO., LTD.

FD210

OJI Paper CO., LTD.

ADP78

OJI Paper CO., LTD.

PD150R

OJI Paper CO., LTD.

Summary of Contents for MONiMAX8200QTN
















































































































Search results

Summary of Contents for MONiMAX8200QTN

Reviews:

Brands by name

Popular brands

Nautilus Hyosung MONiMAX8200QTN, Operator'S Manual

Search results

Summary of Contents for MONiMAX8200QTN

Reviews:

Brands by name

Popular brands