INDUSTRY CANADA COMPLIANCE STATEMENT
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power(e.i.r.p.)is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des
autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1)this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
FCC INFORMATION TO USERS
This equipment has been tested and found to comply with the limits for Class B digital devices,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna;
-Increase the separation between the equipment and receiver;
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Changes or modifications not expressly approved by Nautic Devices Inc. could void
the user’s authority to operate the equipment.
FOR CLASS B – UNINTENTIONAL RADIATORS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operations.
07
SAFETY
WARNING!
Don’t hold Yapalong too close to your head when in use.
GET STARTED
1. Be ware that the antenna cover
is purposely pre-bent for impact
prevention
7. To adjust the sound volume,
press UP or DOWN button, repeatedly
if necessary, until desired volume is
reached. To adjust the microphone
sensitivity, while holding down AUX
button, press UP or DOWN button,
repeatedly if necessary until desired
sensitivity is reached. Now Yapalongs
let every member in the group talk
freely and listen at the same time.
8. To turn Yapalong unit off, hold
POWER button 2 seconds until RED
LED flashes 3 times. Then the unit
powers down.
2.
The rechargeable Lithium
polymer battery is pre-installed to
comply with the shipping regulations.
For future battery replacement,
make sure the battery connector is
plugged into the socket with the
color of the cables matching the
polarity “Red Black” shown on the
case. For your safety, use only battery
provided by Nautic Devices Inc.
3. Turn Yapalong unit on by holding
down POWER button for 2 seconds
until RED LED turns on.
4. If the AMBER LED blinks every 2
or 5 seconds or there is no LED light
at all, battery needs to be charged.
Plug the adaptor to the wall outlet.
Plug the barrel connector of the
cable into the power charging jack.
Turn off the unit during battery
charging will speed up the charge
time. AMBER LED turns on during
charging and GREEN LED turns on
when battery is fully charged.
5. If RED LED remains on with high
intensity, it means it cannot detect
other group unit due to various
reasons: no group unit powered on;
group unit out of range; unit in
different group (refer to “Binding
Procedure” to do grouping).
6. If RED LED remains on with
normal intensity, it means it has
detected group unit(s). Plug in the
headset as show in the figure. The
unit is now ready to be used with
other powered-on group units.
02
