15. FACING THE FRONT SIDE OF THE AMADINDA
HOOK THE CABLE LOOPS FROM THE THE TOP
SIDE OF THE KEYS TO POSTS 'B' AND 'C'.
16.
HOOK THE LOOPS ON THE AMADINDA TO THE
TURNBUCKLE BY LOOSENING THE NUT ON THE
TURNBUCKLE REMOVE THE BOLT, SLIDE THE
CABLE LOOP INTO THE OPENING AND SLIDE
THE BOLT THROUGH THE TURNBUCKLE HOLES,
THROUGH THE CABLE LOOP AND THROUGH THE
OTHER TURNBUCKLE HOLE AND RE-SECURE
THE NUT
17.
REPEAT STEPS 15 & 16 FOR THE OTHER TWO
CABLES ON POSTS 'A' AND 'D'
18.
LOOSEN OR TIGHTEN TURNBUCKLES TO
CORRECT MEASUREMENT TO GET THE
LONGEST KEY TO BE 228mm [9"] OR GREATER
OFF THE FINISHED SURFACE.
18.1.
TURNBUCKLES ON LOWER POSTS ('A' AND
'C') TO HAVE 50mm [2"] GAP BETWEEN
THREADED RODS.
18.2.
TURNBUCKLES ON HIGHER POSTS ('B' AND
'D') TO HAVE 70mm [2
3
4
"] GAP BETWEEN
THREADED RODS.
19.
THE SOARING AMADINDA IS APPROXIMATELY AS
TIGHT AS IS REQUIRED WHEN THERE IS NO
MORE THAN 228mm [9"] BETWEEN THE
LOWEST KEY AND THE GROUND. MEASURE THE
DISTANCE FROM THE POLY-COATED AIRCRAFT
CABLE TO THE POST SIDE OF THE EYE BOLT.
20. CUT HEAT SHRINK FOR EACH POST 1
1
2
" LONGER
THAN YOUR MEASUREMENTS. CUT THE EYE
BOLT SIDE ON THE SAME ANGLE AS IS MADE
BY THE TURNBUCKLE TO THE POST.
21.
DISCONNECT THE SOARING AMADINDA ENDS
(ONE AT A TIME) TO SLIDE THE HEAT-SHRINK
TUBING OVER THE HARDWARE. NOTE: DO NOT
CUT THE HEAT-SHRINK TUBING LENGTH-WISE.
22. ROLL HEAT SHRINK BACK BY 1" - 2" ON THE
POST END OF THE TURNBUCKLE TO EXPOSE
THE BOLT.
23. HANG THE LOSE TURNBUCKLE BACK ON THE
EYE BOLT AND ROLL THE HEAT SHRINK OVER
THE EYE BOLT.
24. SLIDE THE HEAT SHRINK UP OR DOWN TO
ACCESS THE TURNBUCKLE; THIS WILL BE
DIFFICULT, BE PATIENT.
25. TIGHTEN TURNBUCKLE AS PER STEPS 18 & 19.
26. REPEAT STEPS 20 - 25 FOR EACH
TURNBUCKLE
27. USING A HEAT GUN (PAINT STRIPPER), GENTLY
AND EVENLY HEAT THE HEAT-SHRINK FOR IT TO
SHRINK DOWN TIGHT TO THE HARDWARE. (IF IT
SMOKES IT'S TOO HOT; DISTRIBUTE HEAT MORE
EVENLY).
28. HEAT-SHRINK SHOULD COVER ALL HARDWARE
LEAVING EYE BOLT AND THE EYE ON THE
SOARING AMADINDA ONLY PARTIALLY EXPOSED
WITH LESS THAN
3
8
" OF THE HOLE EXPOSED.
29. RESTORE ADJACENT SURFACING TO
PRE-CONSTRUCTION CONDITION UNLESS
OTHERWISE SPECIFIED.
HEAT SHRINK
RECOMMENDED
AMOUNT OF
EXPOSED
HARDWARE
- PLAN -
- ATTACHMENT DETAIL -
N.T.S.
STEP 4: HANGING YOUR SOARING AMADINDA (CAUTION - HEAVY! TWO PEOPLE REQUIRED)
N.T.S.
N
s
INSTRUMENTS
FOR YOUR PLAYGROUND
DETAIL
PRODUCT NUMBER
PAGE
SCALE @ 8.5x11
DRAWN
CHECKED
PHONE NUMBER:
1-877-733-7459
NI-PG-
SOARING AMADINDA: POST MOUNT
403-06
SE
SE
4 OF 4
