background image

Fiber Optic Products Instructions

For indoor use only. Retain carton for storage purposes.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

• Do not use seasonal products outdoors 

unless marked suitable for indoor and 
outdoor use. When products are used in 
outdoor applications, connect the product to 
a Ground Fault Circuit Interrupter (GFCI) 
outlet. If one is not provided, contact a 
qualified electrician for proper installation. 

• This seasonal use product is not intended 

for permanent installation or use. 

• Do not mount or place near gas or electric 

heaters, fireplaces, candles or other similar 
sources of heat. 

• Do not secure the wiring of the product 

with staples or nails, or place on sharp 
hooks or nails. 

• Do not let lamps rest on the supply cord or any wire.  
• Unplug the product when leaving the house, 

when retiring for the night, or if left unattended. 

CAUTION:

 This is an electrical product – not a 

toy! To avoid risk of fire, burns, personal injury 
and electric shock, it should not be played with 
or placed where small children can reach it. 

• Do not use this product for other than its 

intended use. 

• Do not hang ornaments or other objects from 

cord, wire or light string. 

• Keep this product in a well ventilated area, do 

not block any air openings. 

• Do not close doors or windows on the product 

or extension cords as this may damage the 
wire insulation. 

• Do not cover the base with paper, cloth or any 

other material not part of the product when it 
is in use. 

• Never operate this product if the power cord 

or plug is damaged. 

• This product should not be used with a voltage 

converter. 

• Use only manufacturer specified replacement 

bulbs. 

• Do not look directly at any halogen bulb. 
• Read and follow all instructions that are on the 

product or provided with the product.

CAUTION:

 IMPORTANT SAFETY INSTRUCTIONS

Note that some models will have the power supply adapter attached to 
the base.  

1. Place the base on a sturdy flat surface and insert the upper section 

center pole into the center opening of the base. Push the upper 
section in until it is firmly seated. 

Taller trees will include a metal stand rather than a base pot (light 
and motor assembly are attached to bottom of tree center pole). 
Swivel the stand to its fully open position. Put section pole into tree 
stand making sure it is seated properly (Figure 1). Tighten eye bolt. 

2. The tree/topiary/bush can now be shaped by bending and arranging 

the branches into desired positions giving it a natural appearance. 
(The branches are folded in for shipping purposes.) See shaping 
instructions below. 

The base should never be covered with a tree skirt or similar 
covering that may block the ventilation holes. 

3. Plug the power supply adapter jack into the base (where applicable). 

The adapter jack must be plugged into the base before being 
plugged into a power outlet. 

Plug the power supply adapter into a 

standard outlet.

 

Multi-function models will have an additional electrical connection 
between the upper section and base. Plug the wire connector from 
the upper section into the socket on the top of the base (Figure 2). 

Base Assembly

 

(where applicable)

 

Figure 3. Some models of taller fiber optic trees will have 
bases that require separate legs to be attached. Referring 
to the diagram, slide each leg up into the base as follows: 

Line up the pegs on the lower section of leg with the holes 
in the bottom of the base. Hold the leg against the base 
wall and slide it up until the pegs are in the holes; at the 
same time, the tab on the top of the leg will insert into the 
slot beneath the ring at the top of the base. 

Depending on base design, there will be three or four legs. 
Install threes legs as shown in diagram. Use holes opposite 
of each other for four leg models. 

Branch Shaping 

Figure 4

 

Shaping the branches of your product is the last step of 

Figure 1

Figure 2

Figure 4

assembly. The care and attention you give to this final process will result 
in a genuinely beautiful and appealing holiday centerpiece. 

AC adapter should be disconnected from power source. 

1. Make sure the fiber optic tree, topiary or bush is firmly seated in it’s 

base. 

2. Starting at the bottom of the product, fold down each individual 

branch to it’s natural position. Continue working your way up, folding 
down branches on top of the ones below (Figure 3). 

Branches should be carefully pressed back to center when disassembled 
for storage in original carton.

Figure 3

Reviews: