manualshive.com logo in svg

National Semiconductor LM98640CVAL, User Manual

Share
Download
National Semiconductor LM98640CVAL User Manual Download Page 24

Electronic Component Distributor. Source::Texas Instruments

 P.N:LM98640CVAL Desc:EVAL BOARD FOR LM98640 
Web:http://www.hotenda.cn E-mail:[email protected] Phone:(+86) 075583794354

 

 

 
 

 

 

 

   

8.0 Appendix B: Using the AFEval software and the Total Phase Aardvark SPI Interface 

 

IMPORTANT NOTE: Before connecting this board to the PC, please install the AFEval Software from the CDROM 
included with the development kit or file provided by your National Semiconductor representative. (See Appendix 
C) 

Connecting the Development Board before installation may result in the board being registered as an unknown 
USB device. If this happens you will need to uninstall the device using the Windows Device Manager before 
installing the AFEval Software. 
 
While using the Total Phase Aardvark SPI device, the Wavevision 5 Data Capture board should not be connected. 
 

8.1 Install the device drivers for the Aardvark device. 

The drivers for the Aardvark SPI module should be installed according to the instructions and CD which accompanied the 
device. 
 

8.2 Connecting the Aardvark SPI device and LM98640CVAL board for the first time 

 

To facilitate external test equipment based data capture, the LM98640CVAL development board allows for SPI 
communication through a 2x5 dual row header.  The Total Phase Aardvark SPI device is supplied to provide this 
communication using the AFEval software. 

1.  With all power off, and the USB cable disconnected, connect the Aardvark device to the LM98640CVAL board 

(connector JF3).   

2.  Configure the JP6 and JP7 jumpers on the LM98640CVAL board for the desired power supply source.  While 

using the external SPI (and not the WV5 board), the power for the LM98640CVAL board should be configured via 
pins 3-4 or 5-6 on the JP6 and JP7 connectors. 

3.  Connect the USB cable from the PC to the Aardvark device. 

4.  Allow time for the PC to detect the Aardvark board and load the appropriate drivers. 

5.  Start the AFEval software. 

 
 

                            24 / 27

Summary of Contents for LM98640CVAL




























Reviews:

No comments

Brands by name

Popular brands

Load more brands