background image

GB - 5

SAFETY RULES

Read, understand, and follow all safety 
practices in Owner/Operator Manual before 
beginning assembly. Failure to follow 
instructions could result in personal injury 
and/or damage to unit.

Complete a walk around inspection of unit 
and work area to understand:
  • Work area   • Your unit   • All safety decals

Determine which attachments are needed 
and can be used safely.

Inspect unit before each use for: missing or 
damaged decals and shields, correctly 
operating safety interlock system, and 
deterioration of grass catchers. Replace or 
repair as needed.

ALWAYS check overhead and side 
clearances carefully before operation. 
ALWAYS be aware of traffic when operating 
along streets or curbs.

Keep children and people away. 
Keep children out of work area and under 
watchful care of a responsible adult.

Keep area of operation clear of all toys, pets, 
and debris. Thrown objects can cause injury. 

Check for weak spots on docks, ramps or 
floors. Avoid uneven work areas and rough 
terrain. Stay alert for hidden hazards or traffic.
DO NOT operate near drop-offs, ditches, or 
embankments. Unit can suddenly turn over if 
a wheel is over the edge of a cliff or ditch, or if 
an edge caves in.

Data indicates that operators, age 60 and 
above, are involved in a larger percentage of 
riding mower related injuries. These 
operators should evaluate their ability to 
operate the riding mower safely enough to 
protect themselves and others from serious 
injury.

Read the entire Owner/Operator manual and 
other training material. If the operator or the 
mechanic cannot read the manual, it is the 
owner’s responsibility to explain it to them. 
Only the user can prevent and is responsible 
for accidents or injuries occurring to 
themselves, other people or property.
Only trained adults may operate or service 
unit. Training includes actual operation.

Local regulations may restrict the age of the 
operator.

NEVER allow children to operate or play on 
or near unit. Be alert and shut off unit if 
children enter area.
NEVER operate unit after or during the use of 
medication, drugs or alcohol. Safe operation 
requires your complete and unimpaired 
attention at all times.

DO NOT wear loose clothing or jewelry and 
tie back hair that may get caught in rotating 
parts.

Wear adequate outer garments.
NEVER wear open sandals or canvas shoes 
during operation. Wear adequate safety gear, 
protective gloves and footwear.
Wear proper footwear to improve footing on 
slippery surfaces.

2

Summary of Contents for 99500500-8400

































Reviews: