manualshive.com logo in svg

National Instruments VXI-AO-48XDC, User Manual, Page: 23 / 58

Share
Download
National Instruments VXI-AO-48XDC User Manual Download Page 23

Chapter 3

Signal Connections

©

 National Instruments Corporation

3-5

VXI-AO-48XDC User Manual

Refer to Appendix A, 

Specifications

, for detailed information.

Analog Output Signal Connections

Both voltage and current outputs are available on the VXI-AO-48XDC. 
This section describes how to make connections for each type of output. 
Figure 3-3 shows how to connect the voltage channel (VCH) outputs.

Figure 3-3.  

VCH Connection as a Voltage Output

C<32..9>

AGND

Analog Ground—These pins are connected 
to the VXI-AO-48XDC analog ground 
plane. All VXI-AO-48XDC ground planes 
connect to the VXIbus system ground signal.

C<8..2>

DGND

Digital Ground—These pins are connected 
to the VXIbus system ground signal. All 
VXI-AO-48XDC ground planes connect to 
the VXIbus system ground signal.

Table 3-2.  

CH<24..47> Connector Descriptions (Continued)

Pin

Signal Name

Description

AGND

A

Load

±

10.1 V

VCH

Floating Load

Summary of Contents for VXI-AO-48XDC



























































Reviews:

No comments