National Instruments VMEpc 600 series, User Manual, Page: 34 / 88

Share

Page: 34 / 88

National Instruments VMEpc 600 series User Manual Download Page 34

Chapter 3

Configuration and Installation

VXI/VMEpc 600 Series User Manual

3-14

©

National Instruments Corporation

backplane receptacle connectors. Using slow, evenly distributed
pressure, press the module straight in until it seats in the expansion
slot. The front panel of the VXI/VMEpc 600 Series should be even
with the front panel of the mainframe.

4.

Tighten the retaining screws on the top and bottom edges of the front
panel.

5.

Check the installation.

6.

Connect the keyboard and mouse to the appropriate connectors. Use
the keyboard adapter cable that your received with your kit to adapt
AT-style keyboards to the VXI/VMEpc 600 Series mini-DIN
connector.

7.

Connect the VGA monitor video cable to the VGA connector.

8.

Connect devices to ports as required by your system configuration.
Some ports, such as the COM ports, have adapter cables that you can
order from National Instruments.

9.

Replace or close any doors or covers to the mainframe.

«
...
32
33
34
35
36
...
»

Summary of Contents for VMEpc 600 series

























































































Reviews:

No comments