background image

TC-2095 Terminal Block Calibration Procedure

2

ni.com

Equipment and Other Test Requirements

This section describes the equipment, software, documentation, and test
conditions required for verifying the performance of the TC-2095.

Test Equipment

Verification requires a high-precision voltage source with at least 50 ppm
accuracy, a multiranging 5 1/2 digit digital multimeter (DMM) with
15 ppm accuracy, and a thermometer that is accurate to within 0.1

°

C.

NI recommends you use the following instruments for verifying the
performance of the TC-2095:

Calibrator—Fluke 5700A

DMM—NI 4060 or Agilent 34401A

Note

You also need three test connector adapters that fit the 96-pin connector pins.

Use a Pomona 3560 banana jack to test adapter connector (0.040 in. diameter pins) or
an equivalent connector.

If these instruments are not available, use the accuracy requirements listed
above to select a substitute calibration standard.

Software and Documentation

You can find all the necessary information to verify the performance
of the TC-2095 in this verification procedure. No other software or
documentation is required. If you would like more information on the
TC-2095, refer to the

BNC/TC-205 Rack-Mount Adapter Installation

Guide

, which you can download from the NI Web site at

ni.com/manuals

.

Test Conditions

Follow these guidelines to optimize the connections and the environment
during verification:

Keep connections to the TC-2095 terminal block short. Long cables
and wires act as antennae, picking up extra noise that can affect
measurements.

Use shielded copper wire for all cable connections to the terminal
block. Use twisted-pair wire to eliminate noise and thermal offsets.

Keep relative humidity below 80%.

Maintain a temperature between 15 and 35

°

C.

Summary of Contents for TC-2095







Reviews: