background image

RM-4339 Calibration Procedure

|

© National Instruments

|

3

Test Equipment

Table lists the equipment recommended for the performance verification procedures. If the 
recommended equipment is not available, select a substitute using the requirements listed in 
Table 1.

Table 1.  

Recommended Equipment

Equipment

Recommended 

Model

Requirements

Calibrator

Fluke 5520A

If this instrument is unavailable, use a 
calibrator that can provide resistance 
values in the range of 120 

 to 1 k

 with 

0.01

 resolution, and an accuracy of 

90 ppm or better, and can sink 15 mA on 
the 120

 setting, 8 mA on the 350 

 

setting, and 3 mA on the 1 k

 setting.

Ohm Meter

NI PXI-4070

If this instrument is unavailable, use a 
6 ½ digit DMM with 2-wire resistance 
measurement capability and resistance 
accuracy of 80 ppm or better of reading 
+6 ppm of range for the 100 k

 range.

8-Channel 
Universal-Bridge Input 
Module

NI PXIe-4339

Terminal Block 
Connection Accessory

TB-4339/B/C

PXI Express Chassis

NI PXIe-1062Q

Accessory Cable

SH96-96-2

The SH96-96-2 is available in 1 meter, 
3 meter and 5 meter lengths. Any of these 
cable lengths can be used.

RJ50 to Pigtail Cable (8)

NI P/N: 195950-02

An RJ50 cable with a cable wire 
resistance < 0.2 

 with better than 10% 

resistance mismatch between individual 
wires.

Summary of Contents for RM-4339














Reviews: