manualshive.com logo in svg

National Instruments PXI-8820, User Manual

Share
Download
National Instruments PXI-8820 User Manual Download Page 50

Chapter 3

I/O Information

©

 National Instruments 

3-9

NI PXI-8820 User Manual

Universal Serial Bus

Figure 3-6 shows the location and pinouts for the Universal Serial Bus 
(USB) connector on the NI PXI-8820. Each controller has six USB ports 
on the front panel. Table 3-7 lists and describes the USB connector signals.

Figure 3-6.  

USB Connector Location and Pinout

Caution

To ensure the specified EMC performance, install a snap-on ferrite (National 

Instruments part number 711849-01) in accordance with the product installation 
instructions.

Install a noise-suppression ferrite (included in your shipping kit) around all attached 
external USB cables to ensure that your device meets all EMC standards applicable to your 
country. Install the ferrite so that each USB cable loops through the ferrite as shown in 
Figure 3-7. The ferrite should be installed so that it is approximately 50 to 75 mm (2 to 

Table 3-7.  

USB Connector Signals

Pin

Signal Name

Signal Description

1

VCC

Cable Power (+5 V)

2

-Data

USB Data -

3

+Data

USB Data +

4

GND

Ground

USB

4

1

NI PXI-8820

Embedded Controller

USER2

USER2

USER1

USER1

ACT/

ACT/

LINK

LINK

10/

0/100

00

/1000

/1000

PWR OK /

K /

FAULT

FAULT

DRIVE

RIVE

TRIG

RIG

RESET

RESET

Summary of Contents for PXI-8820

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands