background image

Chapter 3

Signal Connections

©

 National Instruments Corporation

3-5

PCI/PXI-6703/6704 User Manual

Current Output for the 6704

You can connect a floating or grounded load to your 6704 device at the 
current output channel. You do not need an external floating power supply 
to complete the controlled current loop. You can control the current loop 
from 0.1 to 20.2 mA. The compliance for the current loop is 0 V to 
10 VDC.

Warning

Because 6704 devices are not electrically isolated from high voltages, a load 

with high common-mode voltages can damage the 6704 devices. National Instruments is 

NOT

 liable for any damages resulting from any such signal connections. 

Figure 3-3 shows how to connect a current channel (ICH) as a current 
output.

Figure 3-3.  

ICH Connection as a Current Output

Because each current channel shares a ground line with a voltage channel, 
you should try to minimize the effect of the return current from your current 
channel on the voltage that you are outputting on your voltage channel. For 
example, if you output 20 mA on a current channel and return that current 
to the 6704 device along the shared ground line in a cable with an 
impedance of 0.1 

, you will see a 2 mV drop in the voltage output by the 

AGND

ICH

PCI/PXI-6704

Load

0.1 to 20.2 mA

Summary of Contents for PCI-6703













































Reviews: