background image

 

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the 

Terms of Use

 section on 

ni.com/legal

 for more information about National Instruments trademarks. Other product and company names mentioned herein are 

trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: 

Help»Patents

 in your software, the 

patents.txt

 file on your CD, or 

ni.com/patents

.

© 2003–2008 National Instruments Corporation. All rights reserved.

373652E

Mar08

CE Compliance

This product meets the essential requirements of applicable European 
Directives, as amended for CE marking, as follows:

2006/95/EC; Low-Voltage Directive (safety)

2004/108/EC; Electromagnetic Compatibility Directive (EMC)

Note

Refer to the Declaration of Conformity (DoC) for this product for any additional 

regulatory compliance information. To obtain the DoC for this product, visit 

ni.com/

certification

, search by model number or product line, and click the appropriate link 

in the Certification column.

Environmental Management

National Instruments is committed to designing and manufacturing 
products in an environmentally responsible manner. NI recognizes that 
eliminating certain hazardous substances from our products is beneficial 
not only to the environment but also to NI customers.

For additional environmental information, refer to the 

NI and the 

Environment

 Web page at 

ni.com/environment

. This page contains the 

environmental regulations and directives with which NI complies, as well 
as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of their life cycle, all products 

must

 be sent to a WEEE recycling 

center. For more information about WEEE recycling centers and National Instruments 
WEEE initiatives, visit 

ni.com/environment/weee.htm

.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 (RoHS)

DŽ

݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/environment/rohs_china

DŽ

(For information about China RoHS compliance, go to 

ni.com/environment/rohs_china

.)

Summary of Contents for NI TB-2634









Reviews: