National Instruments NI PXIe-8130 User Manual Download

Page: 62 / 84

Chapter 4

Common Configuration Questions

National Instruments Corporation

4-5

NI PXIe-8130 User Manual

National Instruments offers the following types of SO-DIMMs for use with
the NI PXIe-8130 controller.

•

PC2-5300 (DDR2 667) 1 GB, 128 MB

64, CL 5, 1.18 in. max

(NI part number 780031-1024)

Note

National Instruments has tested and verified that the DDR2 SO-DIMMs we sell

work with the NI PXIe-8130. We recommend you purchase your DDR2 SO-DIMM
modules from National Instruments. Other off-the-shelf DDR2 SO-DIMM modules
are not guaranteed to work properly.

Figure 4-2.

Installing a DDR2 SO-DIMM in an NI PXIe-8130 Controller

How do I flash a new BIOS?

You can download the new BIOS from

ftp.ni.com/support/pxi

For more information, refer to KnowledgeBase 2GIGKD0Z,

Determining

and Upgrading PXI and VXI Embedded Controller BIOS Versions

DDR2

O-DIMM Mod

DDR2

O-DIMM

ocket

Summary of Contents for NI PXIe-8130





















































































Search results

Summary of Contents for NI PXIe-8130

Reviews:

Related manuals for NI PXIe-8130

Brands by name

Popular brands

National Instruments NI PXIe-8130, User Manual

Search results

Summary of Contents for NI PXIe-8130

Reviews:

Related manuals for NI PXIe-8130

Brands by name

Popular brands