National Instruments NI PXI-6682H User Manual Download

Page: 14 / 65

National Instruments Corporation

2-1

NI PXI-6682 User Manual

Installing and Configuring

This chapter describes how to install the NI PXI-6682 hardware and
software and how to configure the device.

Installing the Software

Refer to the

readme.htm

file that accompanies the

NI-Sync

CD for

software installation directions.

Note

Be sure to install the driver software

before

installing the NI PXI-6682 hardware.

Installing the Hardware

The following are general installation instructions. Consult the chassis user
manual or technical reference manual for specific instructions and
warnings about installing new modules.

Power off and unplug the chassis.

Choose an available PXI slot in the PXI chassis.

Note

The NI PXI-6682 is usually installed in Slot 2.

Remove the filler panel for the PXI slot you chose in step 2.

Ground yourself using a grounding strap or by touching a grounded
object. Follow the ESD protection precautions described in the

Unpacking

section of Chapter 1,

Introduction

Insert the NI PXI-6682 into the PXI slot. Use the injector/ejector
handle to fully insert the module into the chassis.

Screw the front panel of the device to the front panel mounting rail of
the chassis.

Visually verify the installation. Make sure the module is not touching
other modules or components and is fully inserted into the slot.

Plug in and power on the chassis.

The NI PXI-6682 is now installed.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for NI PXI-6682H


































































Search results

Summary of Contents for NI PXI-6682H

Reviews:

Related manuals for NI PXI-6682H

Brands by name

Popular brands

National Instruments NI PXI-6682H, User Manual

Search results

Summary of Contents for NI PXI-6682H

Reviews:

Related manuals for NI PXI-6682H

Brands by name

Popular brands