background image

The file system of the cRIO-9065 follows conventions established for UNIX-style operating
systems. Other LabVIEW Real-Time targets follow Microsoft Windows-style conventions. In
order to facilitate the porting of applications from those targets, this target supports the
Windows-style 

/C

 home directory. This path is bound to the UNIX-style directory 

/home/

lvuser

.

Various LabVIEW Real-Time system files which would be accessible from 

C:

 (or 

/C

) on

other LabVIEW Real-Time targets are found in different locations on this target.

UNIX-style file systems support the concept of a symbolic link, which allows access to a file
using an alternative file path. For example, it is possible to link 

/C/ni-rt/system

, where

dynamic libraries are deployed on other LabVIEW Real-Time targets, to 

/usr/local/lib

,

where they are stored on the cRIO-9065, if the application requires this.

For more information, visit 

ni.com/info

 and enter the Info Code 

RT_Paths

.

Mounting the Device

To obtain the maximum allowable ambient temperature of 70 °C, you must mount the
cRIO-9065 horizontally on a flat, metallic, vertical surface such as a panel or wall. You can
mount the cRIO-9065 directly to the surface or use the NI Panel Mounting Kit. The following
figure shows the cRIO-9065 mounted horizontally.

Figure 6. cRIO-9065 Horizontal Mounting

 

1

1. Up

You can also mount the cRIO-9065 in other orientations, on a nonmetallic surface, on a
35-mm DIN rail, on a desktop, or in a rack. Mounting the cRIO-9065 in these or other
configurations can reduce the maximum allowable ambient temperature and can affect the
typical accuracy of modules in the cRIO-9065. For more information about typical accuracy
specifications for C Series modules and temperature deratings caused by different mounting
configurations, visit 

ni.com/info

 and enter the Info Code 

criotypical

.

Caution

 

Make sure that no C Series modules are in the cRIO-9065 before

mounting it.

Tip

 

Before using any of these mounting methods, record the serial number from

the back of the cRIO-9065 so that you can identify the cRIO-9065 in MAX. You
will be unable to read the serial number after you mount the cRIO-9065.

NI cRIO-9065 User Manual

  | 

© National Instruments

  | 

15

Summary of Contents for NI cRIO-9065



























Reviews: