background image

© National Instruments

|

5-31

NI cDAQ-9138/9139 User Manual

Frequency Generation

You can generate a frequency by using a counter in pulse train generation mode or by using the 
frequency generator circuit, as described in the 

Using the Frequency Generator

 section.

Using the Frequency Generator

The frequency generator can output a square wave at many different frequencies. The frequency 
generator is independent of the four general-purpose 32-bit counter/timer modules on the cDAQ 
chassis.

Figure 5-34 shows a block diagram of the frequency generator.

Figure 5-34.  

Frequency Generator Block Diagram

The frequency generator generates the Frequency Output signal. The Frequency Output signal 
is the Frequency Output Timebase divided by a number you select from 1 to 16. The Frequency 
Output Timebase can be either the 20 MHz Timebase, the 20 MHz Timebase divided by 2, or 
the 100 kHz Timebase.

The duty cycle of Frequency Output is 50% if the divider is either 1 or an even number. For an 
odd divider, suppose the divider is set to D. In this case, Frequency Output is low for (D + 1)/2 
cycles and high for (D - 1)/2 cycles of the Frequency Output Timebase.

Figure 5-35 shows the output waveform of the frequency generator when the divider is set to 5.

Figure 5-35.  

Frequency Generator Output Waveform

Frequency Output can be routed out to any PFI terminal. All PFI terminals are set to 
high-impedance at startup. The FREQ OUT signal also can be routed to many internal timing 
signals.

In software, program the frequency generator as you would program one of the counters for 
pulse train generation.

100 kHz Time

bas

e

20 MHz Time

bas

e

Fre

qu

ency

O

u

tp

u

t

Time

bas

e

FREQ OUT

Divi

s

or

(1–16)

Fre

qu

ency Gener

a

tor

÷

 

2

Fre

qu

ency

O

u

tp

u

t

Time

bas

e

FREQ OUT

(Divi

s

or = 5)

Summary of Contents for NI cDAQTM-9138














































































































































Reviews: