background image

©

 National Instruments Corporation

7

Getting Started with the NI 8234

FCC Class B User Information

This equipment has been tested and found to comply with the limits for the class B digital device 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. The equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. 

If this equipment does cause harmful interference to television or radio reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference 
by one or more of the following means:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution

If the device is changed or modified, the user may void his or her authority to operate the 

equipment.

Note

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.

Note

Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory 

compliance information. To obtain the DoC for this product, visit 

ni.com/certification

search by model number or product line, and click the appropriate link in the Certification column.

Environmental Management

National Instruments is committed to designing and manufacturing products in an environmentally 
responsible manner. NI recognizes that eliminating certain hazardous substances from our products is 
beneficial not only to the environment but also to NI customers.

For additional environmental information, refer to the 

NI and the Environment

 Web page at 

ni.com/environment

. This page contains the environmental regulations and directives with which 

NI complies, as well as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of their life cycle, all products 

must

 be sent to a WEEE recycling center. 

For more information about WEEE recycling centers and National Instruments WEEE initiatives, 
visit 

ni.com/environment/weee.htm

.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 (RoHS)

DŽ

݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/environment/rohs_china

DŽ

(For information about China RoHS compliance, go to 

ni.com/environment/rohs_china

.)

Summary of Contents for NI 8234









Reviews: