National Instruments Network Adapter NI PXIe-1075 User Manual Download

Page: 56 / 78

National Instruments Corporation

B-1

Pinouts

This appendix describes the connector pinouts for the NI PXIe-1075
chassis backplane.

Figure B-1 illustrates the types of PXIe connectors by providing a layout of
the PXI Express system controller slot (slot 1).

Table B-1 shows the XP4 Connector Pinout for the System Controller slot.

Table B-2 shows the XP3 Connector Pinout for the System Controller slot.

Table B-3 shows the XP2 Connector Pinout for the System Controller slot.

Table B-4 shows the XP1 connector pinout for the System Controller slot.

Table B-5 shows the XP4 Connector Pinout for the System Timing slot.

Table B-6 shows the XP3 Connector Pinout for the System Timing slot.

Table B-7 shows the TP2 Connector Pinout for the System Timing slot.

Table B-8 shows the TP1 Connector Pinout for the System Timing slot.

Table B-9 shows the XP4 Connector Pinout for the Hybrid peripheral slots.

Table B-10 shows the XP3 Connector Pinout for the Hybrid
peripheral slots.

Table B-11 shows the P1 connector pinout for the Hybrid peripheral slots.

For more detailed information, refer to the

PXI-5 PXI Express Hardware

Specification

, Revision

2.0

. Contact the PXI Systems Alliance for a copy

of the specification.

Summary of Contents for Network Adapter NI PXIe-1075















































































Search results

Summary of Contents for Network Adapter NI PXIe-1075

Reviews:

Related manuals for Network Adapter NI PXIe-1075

Brands by name

Popular brands

National Instruments Network Adapter NI PXIe-1075, User Manual

Search results

Summary of Contents for Network Adapter NI PXIe-1075

Reviews:

Related manuals for Network Adapter NI PXIe-1075

Brands by name

Popular brands